Previous Thread
Index
Next Thread
Print Thread
Go To
Page 1 of 2 1 2
Beginners Forum
Joined: Jan 2017
Posts: 18
F
Enthusiast
OP Offline
Enthusiast
F
Joined: Jan 2017
Posts: 18
Hello all -

First post for this newbie. I liken working with computers and software to learning to drive an 18-wheel rig: it's cumbersome, it's slow, I'm lumbering, there's a lot of gears to navigate, a lot of mistakes, etc. etc.

So I'm muddling thru Windows BIAB 2016 w/ 2017 upgraded RTs.

I created a song on my laptop (Windows 10), converted it to .mp3 and e-mailed it to my PC (Windows 7) to play on iTunes, but it sounds faint and dull on the PC.

The mp3 version sounds great on the laptop, tho the file is identified as .WAV and not mp3 as I had specified at file conversion. What gives?

Thanks.

Beginners Forum
Joined: Dec 2003
Posts: 20,638
Veteran
Offline
Veteran
Joined: Dec 2003
Posts: 20,638
MP3s compress the data. In other words you will lose data when you use MP3. The more compression you use the more data you lose. This is called lossy compression. If you chose 128 kbps then you will lose a lot of data. Lower than 128 kbps MP3s are really terrible. To get wav type quality you should use 320 kbps MP3s, although 192 kbps and up also sound OK with some genres of music.

Wavs do not compress data so that is why they sound so good. There are other music file compression programs that do not lose data. Programs like Flac and Ape are two such programs. They are called lossless programs. If you have a player that can use either of these that would be the optimum way to go IMO. Otherwise use MP3s that are 192 kbps or higher.

Note that sometimes when sending others 128 kbps MP3s I have had to have a song set for wav and another version of the song mixed for MP3. However if you use the 192 kbps or higher you should not have to do this. YMMV

PS - I use the free Audacity program for converting wavs to MP3s.

{edit} - I forgot to say welcome to the most friendliest site on the web!

Last edited by MarioD; 01/31/17 06:49 AM.

Me, it's not about how many times you fail, it's about how many times you get back up.
Cop, that's not how field sobriety tests work.

64 bit Win 10 Pro, the latest BiaB/RB, Roland Octa-Capture audio interface, a ton of software/hardware
Beginners Forum
Joined: Dec 2000
Posts: 12,580
Veteran
Offline
Veteran
Joined: Dec 2000
Posts: 12,580
If you render your MP3s at 256 or 320, I find almost imperceptible differences in the sound. When I rip my music, I generally rip it twice. Once at 128 for my iPod Classic that gets used in the car (where there is lots of noise anyway, and that allows for a lot of songs) and again at 320 for playback on my home audio system (a much better listening environment).

And just to clarify, Mario, is talking about lossy data compression (ripping to different audio formats, such as MP3 or WMA), not audio compression (such as running a VSTi compressor). Two completely different things.


John

Laptop-HP Omen I7 Win11Pro 32GB 2x2TB, 1x4TB SSD
Desktop-ASUS-I7 Win10Pro 32GB 2x1.5TB, 2x2TB, 1x4TB SATA

BB2024/UMC404HD/Casios/Cakewalk/Reaper/Studio One/MixBus/Notion/Finale/Dorico/Noteworthy/NI/Halion/IK

http://www.sus4chord.com
Beginners Forum
Joined: Jan 2017
Posts: 18
F
Enthusiast
OP Offline
Enthusiast
F
Joined: Jan 2017
Posts: 18
Thanks for the quick response, guys, but back up the truck a second...

Where am I specifying a kbps?

I hit the WAV icon, giving me "Export Song as Audio," then I click "Export as MP3," then Save (to my desktop). I attach it to an email & send to the PC to open in iTunes: dullness ensues.

Beginners Forum
Joined: Dec 2000
Posts: 12,580
Veteran
Offline
Veteran
Joined: Dec 2000
Posts: 12,580
If you haven't installed updated codecs on your computer, you may very well be getting 56kbps encoding by default.

I generally don't do it directly from BIAB; I usually just export to WAV and from there convert to MP3 using a dedicated program, where I can choose my codec (usually LAME) and bit rate settings.


John

Laptop-HP Omen I7 Win11Pro 32GB 2x2TB, 1x4TB SSD
Desktop-ASUS-I7 Win10Pro 32GB 2x1.5TB, 2x2TB, 1x4TB SATA

BB2024/UMC404HD/Casios/Cakewalk/Reaper/Studio One/MixBus/Notion/Finale/Dorico/Noteworthy/NI/Halion/IK

http://www.sus4chord.com
Beginners Forum
Joined: Dec 2003
Posts: 20,638
Veteran
Offline
Veteran
Joined: Dec 2003
Posts: 20,638
Thanx John for clarifying. I wasn't even thinking about audio compression when I wrote that message! My bad! I should have specified the difference but I'm glad that you did.


Me, it's not about how many times you fail, it's about how many times you get back up.
Cop, that's not how field sobriety tests work.

64 bit Win 10 Pro, the latest BiaB/RB, Roland Octa-Capture audio interface, a ton of software/hardware
Beginners Forum
Joined: Dec 2003
Posts: 20,638
Veteran
Offline
Veteran
Joined: Dec 2003
Posts: 20,638
I use Audacity for all of my conversions. You can download
Audacity here:

http://www.audacityteam.org/download/windows/

Then scroll down and download LAME MP3 encoder from the same page.

If you look at Audacity you will see that you can do a lot more than conversions with it.

When converting a wav to a MP3 you can choose from many data compressions. Click on File/Export Audio and scroll down to MP3 files in Save as type. Then click on Options and pick your kbps in the scroll down arrow in the Quality window: see attached image.



Me, it's not about how many times you fail, it's about how many times you get back up.
Cop, that's not how field sobriety tests work.

64 bit Win 10 Pro, the latest BiaB/RB, Roland Octa-Capture audio interface, a ton of software/hardware
Beginners Forum
Joined: May 2000
Posts: 21,609
Veteran
Offline
Veteran
Joined: May 2000
Posts: 21,609
FWIW, as far as I know, mp3 format has a 16kHz top end cutoff regardless of the bitrate, so you lose something in the top end no matter what. Regardless of codec or software used.


Make your sound your own!
.. I do not work here, but the benefits are still awesome
Beginners Forum
Joined: Aug 2011
Posts: 10,099
Veteran
Offline
Veteran
Joined: Aug 2011
Posts: 10,099
Originally Posted By: rharv
FWIW, as far as I know, mp3 format has a 16kHz top end cutoff regardless of the bitrate, so you lose something in the top end no matter what. Regardless of codec or software used.


I had not heard that but it makes sense. A search came up with an article that states MP3 top end frequency cut off is related to the sampling conversion. The chart below is copied from ++ THIS ++ link.

bit rate > cut-off frequency > compression
1411kbps > 20kHz > 1:1
320kbps > 19.5kHz > 1:4.4
192kbps > 18kHz > 1:7.3
160kbps > 17kHz > 1:8.8
128kbps > 16kHz > 1:11
96kbps > 15kHz > 1:14.7
64kbps > 11kHz > 1:22
32kbps > 5kHz > 1:44


Jim Fogle - 2024 BiaB (1109) RB (Build 3) Ultra+ PAK
Cakewalk - Zoom MRS-8 recorder
Desktop: i7 Win 10 build 2004, 12GB ram 256GB SSD, 4 TB HDD
Laptop: i3 64bit Win 10 build 21H2, 8GB ram 500GB HDD
Music at: https://fogle622.wix.com/fogle622-audio-home
Beginners Forum
Joined: Jul 2000
Posts: 25,798
Veteran
Offline
Veteran
Joined: Jul 2000
Posts: 25,798
Check out Nyquist rate for a further explanation.


BIAB 2024 Win Audiophile. Software: Studio One 6.5 Pro, Swam horns, Acoustica-7, Notion 6; Win 11 Home. Hardware: Intel i9, 32 Gb; Roland Integra-7, Presonus Studio 192, Presonus Faderport 8, Royer 121, Adam Sub8 & Neumann 120 monitors
Beginners Forum
Joined: Aug 2011
Posts: 10,099
Veteran
Offline
Veteran
Joined: Aug 2011
Posts: 10,099
Originally Posted By: Matt Finley
Check out Nyquist rate for a further explanation.


Yeah Matt, I'm very familiar with Nyquist as it applies to a wave file but never thought that it applied to lossy MP3 formats. Don't know if I didn't think it through or just had blinders on.

Of course sometimes even I wonder about how much I don't think things through. For instance, do you also know that the only data recorded in a sample is waveform gain? I was dumbfounded when I found that out.


Jim Fogle - 2024 BiaB (1109) RB (Build 3) Ultra+ PAK
Cakewalk - Zoom MRS-8 recorder
Desktop: i7 Win 10 build 2004, 12GB ram 256GB SSD, 4 TB HDD
Laptop: i3 64bit Win 10 build 21H2, 8GB ram 500GB HDD
Music at: https://fogle622.wix.com/fogle622-audio-home
Beginners Forum
Joined: Jul 2000
Posts: 25,798
Veteran
Offline
Veteran
Joined: Jul 2000
Posts: 25,798
Unless I'm mistaken, the Nyquist rate will tell you the highest frequency that can be produced by a specific sample rate, so that would explain why the highs disappear in successively lower MP3 encoding rates.


BIAB 2024 Win Audiophile. Software: Studio One 6.5 Pro, Swam horns, Acoustica-7, Notion 6; Win 11 Home. Hardware: Intel i9, 32 Gb; Roland Integra-7, Presonus Studio 192, Presonus Faderport 8, Royer 121, Adam Sub8 & Neumann 120 monitors
Beginners Forum
Joined: Mar 2004
Posts: 1,753
Expert
Offline
Expert
Joined: Mar 2004
Posts: 1,753
BTW, the trick to getting the free LAME mp3 codec into Audacity's access is you have to go to Edit | Preference and then Library. From there it will install it sort of automagically for you. It will take you to a link at the Audacity website. In that link you will choose LAME or something like that.
Then when you want to convert a .wav to mp3.
In Audacity...
File
Open | navigate to your .wav file. It will import it for you.
File
Export Audio
At the bottom of the Export dialog you can change the compression rate.

Last edited by Tobias; 01/31/17 09:54 PM.

Does the noise in your head bother me ?
Beginners Forum
Joined: Apr 2009
Posts: 9,301
Veteran
Offline
Veteran
Joined: Apr 2009
Posts: 9,301
Originally Posted By: ffreniere


I created a song on my laptop (Windows 10), converted it to .mp3 and e-mailed it to my PC (Windows 7) to play on iTunes, but it sounds faint and dull on the PC.

The mp3 version sounds great on the laptop, tho the file is identified as .WAV and not mp3 as I had specified at file conversion. What gives?



So... what every said above is correct... every time you covert a WAVE file to MP3 you are losing 80% or more of the original data depending on the bit rate of the MP3. I always convert to 320kbs MP3 files unless there is a really good reason not to use 320kbs.

But... lets back up a bit. When you finished the song and exported the wave, did you do anything else to that wave at that point or did you proceed directly to the MP3 converter?

The reason I ask is because many folks at that point will process the wave file with what is called "mastering software" to add some sparkle and thump to the music. I prefer to call it polishing or sweetening the song because "mastering" is something totally different but I am OK calling it "small "m" mastering" as well. It's simply the process of adding compression, reverb, and EQ tweeks to the finished song to make it sound a bit better and more cohesive.

Essentially, when you listen to the Wave or the MP3, there should really be very little sonic difference between the 2 files. Most people would not be able to tell you which one was which. Especially at the higher MP3 bit rates.

You also should understand that the different music players software will affect the sound quality more than the Wave to MP3 conversion. I would check that MP3 on several different players to see if that is the problem. Barring that, go back to the original Wave and do some of the polishing and sweetening I mentioned.

One other thing to check on. Be sure that the exported WAVE is normalized to just under 100%. I like to shoot for 96% on the highest peak. Run some compression first to bring the entire wave into a relatively consistent looking form. You want the finished wave to look like this.



In this photo.... the compression rate is consistent but not as high as it could be because there's quite a few spikes and "airspace" above the main body of the energy. The song is on my website and sounds good. By cranking up the compression a bit more, the song would have gained more "apparent volume" but lost some of it's dynamic range... the difference between the loudest and softest parts of the music. Once you get the compression right, and it might take a few tries if you're not worked with this before, you can then use the normalize function. Normalize brings the highest peak to a designated level that you set relative to 0dB. You don't want to go above 0dB.

As a footnote to the compression thing.... in the picture above, if I had cranked the compression up to max, that section toward the end that is obviously lower in volume would have been indistinguishable from the rest. To much compression is not a good thing.

All of that is important because you mentioned a "faint and dull sounding MP3"..... again, that should not happen if your levels are all correct before you convert to MP3, and you have done some proper sweetening.

I hope this helps you find the reasons for the weak and dull sound you ended up with in the MP3.

Last edited by Guitarhacker; 02/01/17 05:24 AM.
Beginners Forum
Joined: Jan 2016
Posts: 260
Apprentice
Offline
Apprentice
Joined: Jan 2016
Posts: 260
Herb, do you use WavePad for your 'mastering software'?


Andy

BIAB 2017 Ultra
Windows 8 and 10
Scarlet 18i8
Reaper and Mixpad
Beginners Forum
Joined: May 2000
Posts: 21,609
Veteran
Offline
Veteran
Joined: May 2000
Posts: 21,609
Even simpler; use PGRTA plugin (or any other frequency analyzer) and look the frequency range of the mp3. See how much it differs from the same wav file.
The better the analyzer the more you'll notice.

I'm sure quite a bit of real-life results depend on the actual codec/rate being used for the conversion.


Make your sound your own!
.. I do not work here, but the benefits are still awesome
Beginners Forum
Joined: Oct 2016
Posts: 1,558
Expert
Offline
Expert
Joined: Oct 2016
Posts: 1,558
Originally Posted By: ffreniere
Hello all -
First post for this newbie. I liken working with computers and software to learning to drive an 18-wheel rig: it's cumbersome, it's slow, I'm lumbering, there's a lot of gears to navigate, a lot of mistakes, etc. etc.
So I'm muddling thru Windows BIAB 2016 w/ 2017 upgraded RTs.
I created a song on my laptop (Windows 10), converted it to .mp3 and e-mailed it to my PC (Windows 7) to play on iTunes, but it sounds faint and dull on the PC.
The mp3 version sounds great on the laptop, tho the file is identified as .WAV and not mp3 as I had specified at file conversion. What gives?
Thanks.


I think it always will. I'm no expert, but my understanding of history is that Apple wanted to load as many songs on to the 32Mb memory of the iPod as it could. Bear in mind, this was the dark ages of memory. Mine has 4Gb now.
OK, so this guy comes along, takes an MP2 (stereo) and adds a third track.
That third track went along and eliminated everything it could. If there was a pause or a silence, the third track would simply tell the audio file when to cut and when to resume. We're talking high tech nano second stuff, here. Basically, a midi on steroids.
The MP3 are made to be played on portable players. What you are hearing is compression quality. Your machine is probably just fine.


Link: www.soundcloud.com/ed_shaw (Feel Free to Use)
https://drooble.com/edward.shaw/hymn/index.htm
Biab for WIN 2020 -- Win 10 64bit -- Reaper/Audacity
Zoom R-16 -- Tascam DP-03-SD -- SoundTap -- Crescendo --
Beginners Forum
Joined: Apr 2009
Posts: 9,301
Veteran
Offline
Veteran
Joined: Apr 2009
Posts: 9,301
Originally Posted By: Andy A - USA
Herb, do you use WavePad for your 'mastering software'?


Yes.

It's a good program and I use it to listen to and work on my exported waves.

In Wavepad I trim the start and the end, and I also run the normalize function on the wave.

After I have done those chores, I convert it to mp3 in Wavepad.

Wavepad seems to have a player that sounds extremely close to my DAW, which is always a good thing. In other words, it doesn't sound to me like it's adding any color to the sound. AND.... I can't tell any sonic difference in Wavepad between the final Wave and the mp3 that came from it.


You can find my music at:
www.herbhartley.com
Add nothing that adds nothing to the music.
You can make excuses or you can make progress but not both.

The magic you are looking for is in the work you are avoiding.
Beginners Forum
Joined: Dec 2000
Posts: 12,580
Veteran
Offline
Veteran
Joined: Dec 2000
Posts: 12,580
I do the same as Herb, but I use Diamond Cut DC8 to do the same thing. I use it to cut off the front and tail. I use it to normalize the wave, as well as apply any mastering effects. DC8 has a lot of filters and effects, mainly designed for cleaning up records and tapes that have been digitized, but works just as well on audio files I create. And DC8 lets me rip to MP3 (or use a host of other CODECS). We're going to start beta testing DC10 pretty soon, so I'm looking forward to that (I help beta test). They also have a very friendly forum (like here) where you get to interact directly with Craig and Rick (the founders of Diamond Cut).


John

Laptop-HP Omen I7 Win11Pro 32GB 2x2TB, 1x4TB SSD
Desktop-ASUS-I7 Win10Pro 32GB 2x1.5TB, 2x2TB, 1x4TB SATA

BB2024/UMC404HD/Casios/Cakewalk/Reaper/Studio One/MixBus/Notion/Finale/Dorico/Noteworthy/NI/Halion/IK

http://www.sus4chord.com
Beginners Forum
Joined: Jul 2000
Posts: 25,798
Veteran
Offline
Veteran
Joined: Jul 2000
Posts: 25,798
My method is similar to John's. I use Adobe Audition 1.5, which is the old Cool Edit Pro converted to Adobe and patched once before Adobe mucked it up. [I also have Adobe Audition 3 so I know].


BIAB 2024 Win Audiophile. Software: Studio One 6.5 Pro, Swam horns, Acoustica-7, Notion 6; Win 11 Home. Hardware: Intel i9, 32 Gb; Roland Integra-7, Presonus Studio 192, Presonus Faderport 8, Royer 121, Adam Sub8 & Neumann 120 monitors
Previous Thread
Next Thread
Go To
Page 1 of 2 1 2

Link Copied to Clipboard
ChatPG

Ask sales and support questions about Band-in-a-Box using natural language.

ChatPG's knowledge base includes the full Band-in-a-Box User Manual and sales information from the website.

PG Music News
Convenient Ways to Listen to Band-in-a-Box® Songs Created by Program Users!

The User Showcase Forum is an excellent place to share your Band-in-a-Box® songs and listen to songs other program users are creating!

There are other places you can listen to these songs too! Visit our User Showcase page to sort by genre, artist (forum name), song title, and date - each listing will direct you to the forum post for that song.

If you'd rather listen to these songs in one place, head to our Band-in-a-Box® Radio, where you'll have the option to select the genre playlist for your listening pleasure. This page has SoundCloud built in, so it won't redirect you. We've also added the link to the Artists SoundCloud page here, and a link to their forum post.

We hope you find some inspiration from this amazing collection of User Showcase Songs!

Congratulations to the 2023 User Showcase Award Winners!

We've just announced the 2023 User Showcase Award Winners!

There are 45 winners, each receiving a Band-in-a-Box 2024 UltraPAK! Read the official announcement to see if you've won.

Our User Showcase Forum receives more than 50 posts per day, with people sharing their Band-in-a-Box songs and providing feedback for other songs posted.

Thank you to everyone who has contributed!

Video: Volume Automation in Band-in-a-Box® 2024 for Windows®

We've created a video to help you learn more about the Volume Automation options in Band-in-a-Box® 2024 for Windows.

Band-in-a-Box® 2024: Volume Automation

www.pgmusic.com/manuals/bbw2024full/chapter11.htm#volume-automation

Video: Audio Input Monitoring with Band-in-a-Box® 2024 for Windows®

We've created this short video to explain Audio Input Monitoring within Band-in-a-Box® 2024, and included some tips & troubleshooting details too!

Band-in-a-Box® 2024: Audio Input Monitoring

3:17: Tips
5:10: Troubleshooting

www.pgmusic.com/manuals/bbw2024full/chapter11.htm#audio-input-monitoring

Video: Enhanced Melodists in Band-in-a-Box® 2024 for Windows®!

We've enhanced the Melodists feature included in Band-in-a-Box® 2024 for Windows!

Access the Melodist feature by pressing F7 in the program to open the new MultiPicker Library and locate the [Melodist] tab.

You can now generate a melody on any track in the program - very handy! Plus, you select how much of the melody you want generated - specify a range, or apply it to the whole track.

See the Melodist in action with our video, Band-in-a-Box® 2024: The Melodist Window.

Learn even more about the enhancements to the Melodist feature in Band-in-a-Box® 2024 for Windows at www.pgmusic.com/manuals/bbw2024upgrade/chapter3.htm#enhanced-melodist

Band-in-a-Box® 2024 DAW Plugin Version 6: New Features Specifically for Reaper®

New with the DAW Plugin Version 6.0, released with Band-in-a-Box® 2024 for Windows: the Reaper® Panel!

This new panel offers built-in specific support for the Reaper® DAW API allowing direct transfer of Band-in-a-Box® files to/from Reaper® tracks!

When you run the Plugin from Reaper®, there is a panel to set the following options:
-BB Track(s) to send: This allows you to select the Plugin tracks that will be sent Reaper.
-Destination Reaper Track: This lets you select the destination Reaper track to receive media content from the Plugin.
-At Bar: You can select a bar in Reaper where the Plugin tracks should be placed.
-Start Below Selected Track: This allows you to place the Plugin tracks below the destination Reaper track.
-Overwrite Reaper Track: You can overwrite previous content on the destination Reaper track.
-Move to Project Folder: With this option, you can move the Plugin tracks to the Reaper project folder.
-Send Reaper Instructions Enable this option to send the Reaper Instructions instead of rendering audio tracks, which is faster.
-Render Audio & Instructions: Enable this option to generate audio files and the Reaper instructions.
-Send Tracks After Generating: This allows the Plugin to automatically send tracks to Reaper after generating.
-Send Audio for MIDI Track: Enable this option to send rendered audio for MIDI tracks.
-Send RealCharts with Audio: If this option is enabled, Enable this option to send RealCharts with audio.

Check out this video highlighting the new Reaper®-specific features: Band-in-a-Box® DAW Plugin Version 6: New Features Specifically for Reaper®

Band-in-a-Box® 2024 DAW Plugin Version 6: New Features Video

The new Band-in-a-Box VST DAW Plugin Verion 6 adds over 20 new features!

Watch the new features video to learn more: Video: Band-in-a-Box® 2024 - DAW Plugin Version 6 New Features

We also list these new features at www.pgmusic.com/bbwin.plugin.htm.

Forum Statistics
Forums66
Topics81,393
Posts732,477
Members38,441
Most Online2,537
Jan 19th, 2020
Newest Members
zagrajbarke, Ernest J, Izzy, BenChaz, Csofi
38,440 Registered Users
Top Posters(30 Days)
MarioD 195
Al-David 124
DC Ron 113
dcuny 87
rsdean 83
Today's Birthdays
CeeDee, SethMould
Powered by UBB.threads™ PHP Forum Software 7.7.5