Page 1 of 2 1 2 >
You need to be logged in to post on the forum
Topic Options
Index
#122461 - 07/22/11 04:08 PM [Band-in-a-Box for Windows] Has anyone had luck with "LoopBe1" for multiple midi?
Mike Lucich Offline
Enthusiast

Registered: 05/23/07
Posts: 99
Loc: Wilsonville, Oregon (Portland ...
Has anyone successfully used the LoopBe1 virtual midi cable program to send an extra midi signal to a synthesizer or harmonizer while using realtreacks and coyote in biab? I need help with settings. Midi/Audio driver setup recognizes that it is there and I have it set as midi in/ midi out. I have dxi checked (also tried without). I have biab setting for "vocalist" (ch5) and have set my vocalist pro to ch5 and "all" but no midi signal to the harmonizer so far. Any suggestions?

Mike
_________________________
Been there, done that, might do it again, but would rather do something new!

Top
#122462 - 07/22/11 04:34 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: Mike Lucich]
Blake Offline
PG Music Staff

Registered: 03/26/08
Posts: 371
Loc: British Columbia, Canada
The LoopBe1 driver should not be selected for both In and Out. This will cause MIDI feedback. I believe it has a fail-safe that mutes the driver if it detects MIDI feedback, so that could be what is going on.

If you are using the driver for output, then you need another program to use it as input. For example, PowerTracks or RealBand could receive MIDI signals and play out through a DXi synth.

If the Vocalist is hardware, then the LoopBe1 driver would not be necessary. In that case their should be some kind of output driver available in the Band-in-a-Box MIDI output driver list.
_________________________
Blake

PG Music Inc.

Top
#122463 - 07/22/11 05:11 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: Blake]
Mike Lucich Offline
Enthusiast

Registered: 05/23/07
Posts: 99
Loc: Wilsonville, Oregon (Portland ...
Thanks Blake, but that is my problem. BIAB does not support multiple midi and therefore when playing realtracks you can't use another piece of midi hardware like the vocalist. That's why if I want midi instruments playing along side my realtracks I have to use the dxi setting (coyote) and it will not send a separate midi signal out using this configuration.
_________________________
Been there, done that, might do it again, but would rather do something new!

Top
#122464 - 07/23/11 09:06 AM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: Mike Lucich]
silvertones Offline
Veteran

Registered: 05/13/03
Posts: 7207
I don't have LoopBe1 but I've used MIDI YOKE. It's a virtual cable as well.You can have up to 16 virtual cables. You need only one.So here's what you do assuming your soundcard is OK with it. It should be.
1. Use midi yoke 1 as your output driver in BIAB
2. In your host program use midiyoke as your input driver for as many tracks as you need.And assign the approprite channels for those tracks that coincide with the BIAB instrument channels
3. assign each of those tracks to a particular DXi/VSTi
4. Route the audio from those DXi/VSTi to your sound card.
5. In BIAB route the audio to your sound card.RTs & RDs
6. In BIAB go to :OPT./PREFS/output channel
7. In this screen check off "output chords" as set up it'll output basic chords on channel 5.
8. In the host again set a track to receive midiyoke 1 on channel 5
9. set this track to output to your hardware midi interface that is plugged into the midi in of your Vocalist
10. Make sure the Vocalist is set to receive the chord info on channel 5.

This is how I did it in the olden days. Hope this helps.
_________________________
John
ESI Gigaport HD+
Lenovo Turion II /4 Gig Ram/ Win7x64
15.6" Monitor
"The only Band is a Real Band"
http://wintertexaninfo.com/Bands/JohnnyD.html

Top
#122465 - 07/23/11 10:53 AM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: silvertones]
John Conley Offline
Veteran

Registered: 09/28/03
Posts: 8333
Loc: London, Ontario, Canada
I'd get the midi out working first.

I clean out the soloist part.

I change the solo part to Midi ch 5

I set the output chords to Midi ch 5

You should just be able to plug a usb to midi cable into the computer, plug it into the harmonizer and it should work.

On my harmonizer there are presets numbered 1.1 to 9.9

If I embed using f5 at bar 1 a 32 it will set the harmonizer to 3.2 so you can change from one harmony to another on the fly.

I would the the above working, and set Midi out (No in yet) in Opts Prefs Midi Driver

I'd use all Realtracks and watch to see my box work on harmonies.

Once you get that working you can decide if you want to try going back in and using the Dxi, I have not tried that as I use a Ketron or My Jv1010.

I think one step at a time is best, like I said no midi plugged back in.

Once you get that to work I'd simply try clicking on the Dxi and see if the soloist track is still firing midi out on ch 5.
_________________________
John Conley
Musica est vita

Top
#122466 - 07/23/11 08:43 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: John Conley]
Mike Lucich Offline
Enthusiast

Registered: 05/23/07
Posts: 99
Loc: Wilsonville, Oregon (Portland ...
Thanks guys, but still no joy. I'll try again tomorrow. BIAB does list my vocalist pro (usb) under midi outs, so if I choose that and not select dxi it will get me through tonight's gig with my midi harmony. I'll just have to stick with songs that only use real tracks (or take the time to change the midi options for the songs with both realtracks and midi).
I really appreciate you taking the time to help!
Mike
_________________________
Been there, done that, might do it again, but would rather do something new!

Top
#456633 - 02/09/18 12:00 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: Mike Lucich]
axelrod Offline
Journeyman

Registered: 04/13/05
Posts: 401
Loc: ny
I'm responding to this old thread-wanting to use BIAB with midi tracks and an external harmonizer.

1. It seems 32 bit midi yoke won't support my 64 bit Iconnectivity MIO...which is a USB to midi converter and supplies the signal to the harmony machine. So I must look elsewhere

2. The choices are loopbe1 ..... or midiloop software by Tobias Erichsen

Anyone have experience with either for supplying multiple midi outs?
Thanks-

Top
#456639 - 02/09/18 12:33 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: Mike Lucich]
jford Offline
Veteran

Registered: 12/20/00
Posts: 10362
Loc: Pensacola, Florida
LoopBE works fine on 32-bit and 64-bit Windows; however, I would suggesting buying LoopBE30, which gives you up to 30 virtual MIDI in/out ports for $19.90.

I have used it with, for example, Noteworthy Composer (which doesn't support DXi or VSTi synths) by sending MIDI data out to LoopBe and then configuring a standalone synth to receive data from LoopBE.
_________________________
John

HP Win10Pro-64, 8GB
ASUS Win10Pro-64, 16GB
HP Win7Pro-64, 8GB

H/W-Behringer U-Phoria UMC404HD, Casio Kbds
S/W-BB/RB2018/Sonar/Reaper/Studio One/Samplitude/MixBus/Notion/Finale/Noteworthy/NI Komplete/Halion/Garritan/IK
Web-http://www.sus4chord.com

Top
#456642 - 02/09/18 01:22 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: jford]
axelrod Offline
Journeyman

Registered: 04/13/05
Posts: 401
Loc: ny
John-
One external midi channel is sufficient for me. But I have a question:
Since the BIAB "Route all DXI/VST" checkbox now doesn't make sense, will LoopBe offer synth options? In other words what will be the NEW order of midi routing, and how will that interface with BIAB?

Looking at the posts above, i believe "Silvertones" addressing of MidiYoke...will likely apply to LoopBE. You choose it as your output device, check "Route DXI/VST" to a Coyote, etc...... specify a midi channel in Output Chords...and let LoopBE assign that channel to my MIO - USB to Midi hardware converter.

I'll wait till you weigh in on this before the install, John. Thanks as usual for your giving and comprehensive attention.
Dan

Top
#456700 - 02/09/18 06:10 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: Mike Lucich]
jford Offline
Veteran

Registered: 12/20/00
Posts: 10362
Loc: Pensacola, Florida
I believe that is correct, but it's free and easily installed/uninstalled. Just give it a try and you should have your answer in about five minutes. And it doesn't hurt to have it installed. It just adds another MIDI port to your system.
_________________________
John

HP Win10Pro-64, 8GB
ASUS Win10Pro-64, 16GB
HP Win7Pro-64, 8GB

H/W-Behringer U-Phoria UMC404HD, Casio Kbds
S/W-BB/RB2018/Sonar/Reaper/Studio One/Samplitude/MixBus/Notion/Finale/Noteworthy/NI Komplete/Halion/Garritan/IK
Web-http://www.sus4chord.com

Top
#457067 - 02/11/18 02:38 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: jford]
axelrod Offline
Journeyman

Registered: 04/13/05
Posts: 401
Loc: ny
Well...... LoopBe1 is installed but nothing is happening. I click on the tray icon or in Programs, and no midi or monitor window comes up..... just the mute screen. I would happily purchase the 8 port version if it does work. I'm now awaiting a response from the creator.....though a bit skeptical at the moment. And others online have recently expressed difficulty. We'll see

Top
#457148 - 02/12/18 06:42 AM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: Mike Lucich]
axelrod Offline
Journeyman

Registered: 04/13/05
Posts: 401
Loc: ny
O.k. here's the story......LoopBe1 does NOT offer one additional port...it's ONLY one port, so useless for a second midi out in BIAB. I would install LoopBe30- there's a trial. But some user notes first, would be helpful- I don't want to open a midi can of worms. There's another thread about this on the forum. I'll look there.

Top
#457166 - 02/12/18 10:51 AM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: Mike Lucich]
jford Offline
Veteran

Registered: 12/20/00
Posts: 10362
Loc: Pensacola, Florida
That's why it's called LoopBe1, because it's only one port. LoopBE30 is up to 30 ports, but you decide how many you want installed (default is two).

I've had it on my computers for about a decade now and it has never caused problems and has always worked. The only thing to be careful of is to not inadvertently set up a MIDI feedback loop.

And you can just try the trial version. The trial version of LoopBe30 works for 60 minutes after its first use. After every reboot, it will work again for an additional 60 minutes. As I said in the previous post, it is also easily uninstalled if you don't want to use it.
_________________________
John

HP Win10Pro-64, 8GB
ASUS Win10Pro-64, 16GB
HP Win7Pro-64, 8GB

H/W-Behringer U-Phoria UMC404HD, Casio Kbds
S/W-BB/RB2018/Sonar/Reaper/Studio One/Samplitude/MixBus/Notion/Finale/Noteworthy/NI Komplete/Halion/Garritan/IK
Web-http://www.sus4chord.com

Top
#457175 - 02/12/18 12:05 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: axelrod]
Larry Kehl Offline
Veteran

Registered: 06/04/00
Posts: 2050
Loc: New Mexico
First here is some reading that may help with what you are trying to do

http://bandinabox.wikia.com/wiki/Accessing_Multiple_Midi_Ports

Second, I seem to have lost the bubble on this how many outputs that you want BIAB to eventuality feed, sounds like at LEAST two? If yes then you are correct Loopbe 1 BY ITSELF won't help, (see above) – and John already said that (but stand by).

Also if yes, besides a multi-port driver you will ALSO need something like MIDI OX (you knew that right?) if trying to go DIRECT form BIAB OUT to your i Connectivity port. You COULD take BIAB OUTPUT via MIDI Yoke, Loopbe 1, or Loopbe 30 into ANOTHER DAW or standalone VSTi (that has with ability to send MIDI out) and THEN using that DAW/VSTI (as a patch bay) route its MIDI thru or OUT to your iConnectivity port.

Yes I saw you already said MIDI Yoke didn't work (more later). I have and do USE BOTH MIDI Yoke and LoopBe 30, I have and do use MIDI Yoke with a 64-bit Yamaha USB MIDI for my Montage 7 and my Fishman Triple Play (installed using its 64 bit drivers)

Like you and John said Loopbe30 has a trial, TRY IT - it won't hurt anything.


Now about MIDI Yoke:

I’m not doubting you have issues but MIDI Yoke SHOULD work fine with your iConnectivity so not sure why you are having issues??

Even if you know this I’ll mention for others who may not know . You need to route BIAB MIDI OUT to a MIDI Yoke port (#1, # 2, #3, … or #8) THEN use MIDI OX (or similar or another DAW) to connect that single MIDI Yoke port to the multiple MIDI IN’s your trying to drive. And if not using MIDI Ox you are using a a similar "software patch bay" or a DAW that can route MIDI ins to one or more MIDI outs

And if having trouble installing MIDI Yoke in Win 10

https://www.youtube.com/watch?v=kORFzILrdmA


BTW the single Loopbe1 port would work just as well in conjunction with MIDI OX as a single port of MIDI Yoke

===================
Next just me rambling

A MIDI port is a MIDI port as far as the OS (or MIDI) is concerned. Again, I use MIDI YOKE/OX with the 64-bit "drivers" for Yamaha USB support for use to/from a Montage 7 while also using my Fishman Triple Play (and its 64-bit driver) to other VSTi's and DAWS for recording/playing and routing.

The iConnectivty uses a "run of the mill" USB 2 interface (it is backward compatible to 1.1 and the whole thing peice of HW is backward compatible to Win XP SP3 - which is ONLY 32 bit)

the iConnectivty MIDI input (if designed to MIDI spec) is listening for a handshake and data from ANY MIDI input source it cannot tell if the handshake and data at its "input" was generated using 32 software, 64 bit software, or another piece of dedicated MIDI hardware, which is independent of ANY OS

The MIDI Protocol is only 8-bit; furthermore, MIDI data itself is only 7 bits since one bit is a STATUS bit (7 bits can represent 128 things)

good luck
Larry



Edited by Larry Kehl (02/12/18 12:06 PM)
_________________________
Win7&10 Pro 64,i7-2600k,32GB,1OTBs HDD,RX480 8GB,FW-410,MIDIplus4x4,Montage7,Fusion 8HD,QS8,GR-50,Integra7, XV5080,Fantom-XR,QSR,SC-8850,Nanosynth,SPLAT,AD2,ST3,Kontakt 5,Amptube4,way too many other VSTi's - but I'm really a guitar player

Top
#457183 - 02/12/18 01:28 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: Mike Lucich]
Pipeline Offline
Veteran

Registered: 02/05/15
Posts: 2410
Originally Posted By: Mike Lucich
Thanks guys, but still no joy. I'll try again tomorrow. BIAB does list my vocalist pro (usb) under midi outs, so if I choose that and not select dxi it will get me through tonight's gig with my midi harmony. I'll just have to stick with songs that only use real tracks (or take the time to change the midi options for the songs with both realtracks and midi).
I really appreciate you taking the time to help!
Mike


https://www.thepiz.org/plugins/?p=midiOut
https://www.tobias-erichsen.de/software/loopmidi.html
LoopMidi is better than LoopBe (LoopBe tends to mute itself), it's free and can set many ports.

Is it the midi chords you want to send to vocal pro ?
If so then in Options > Prefs > Output chords enable

Chord Types
Channel
Ticks before 0 or early ?
Write track to midi file.
Save Midi > file on disk
File > Import > Melody or Soloist from Midi file

Import saved midi and same channel only

Load midiOut into that track and set it to the usb hardware device or LoopBe or MidiLoop.

Top
#457202 - 02/12/18 03:48 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: Larry Kehl]
axelrod Offline
Journeyman

Registered: 04/13/05
Posts: 401
Loc: ny
Larry-
You didn't ramble a bit, and gave me a most generous answer. Thanks so much. With a Windows 7 machine and a Yamaha 144 sound module, I never had an audio or midi issue. Also, Midi Ox/Yoke was my religion during a long, XP tenure. But things changed this weekend.
I suddenly got the whim to pull out my old Helicon Voice Live, and while many Ox/Yoke 64 bit postings seemed discouraging, I took the Ox plunge. But after installation....more posts made me second guess this, and I uninstalled Ox.
The moment of grief arrived after that uninstall, Larry....when BIAB suddenly would play nothing without a yellow error message that there is no Audio driver present in Windows. The message would disappear, and the program would then play. But how an OX uninstall could corrupt my Yamaha 144 audio driver was a mystery. Other audio apps gave the same message. So I tried to reinstall my Yamaha audio driver..... and that FAILED ...saying 'Please telephone the company' A system restore to the pre-OX state brought things back in line. But as the Chinese say, "Once bitten by a snake, for 10 years you're even afraid of a rope"
My second venture of this past weekend involved LoopBe, but emails to creator Daniel Schmidtt, failed to garner help. So in light of your vast knowledge on these specific subjects, I guess you're my guide on 64 bit BIAB midi.
If there is an Ox version other than the latest standard 896 KB version whose uninstall somehow corrupted my Yamaha audio driver, please point the way. And if Yoke and OX still work as efficiently ina 64 bit system as you claim, there's no need for LoopBe at all. Any insights would be helpful. Thanks again.

Top
#457219 - 02/12/18 05:46 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: axelrod]
Larry Kehl Offline
Veteran

Registered: 06/04/00
Posts: 2050
Loc: New Mexico
Don't know what to tell you. So try Pipeline's Loopmidi

I'll now ALSO try LoopMIDI just for grins(thanks Pipeline!) .

but as an FYI I am NOT running Win 10 version 1709 (aka fall creators edition) - so maybe....???

I'm still on last springs version (1703) and will SKIP 1709 completely (and may even skip next one version 1803 coming VERY soon to a PC near you) - depending on what the Win 10 Home users (AKA guinea pig's or uncompensated beta testers) report as issues.


Larry
_________________________
Win7&10 Pro 64,i7-2600k,32GB,1OTBs HDD,RX480 8GB,FW-410,MIDIplus4x4,Montage7,Fusion 8HD,QS8,GR-50,Integra7, XV5080,Fantom-XR,QSR,SC-8850,Nanosynth,SPLAT,AD2,ST3,Kontakt 5,Amptube4,way too many other VSTi's - but I'm really a guitar player

Top
#457225 - 02/12/18 06:35 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: Pipeline]
axelrod Offline
Journeyman

Registered: 04/13/05
Posts: 401
Loc: ny
Pipeline's method of just using Real Tracks is what I've been doing until a more viable solution materializes. Yes, ....I currently output chords to the IConnectivity MIO...my selected midi output driver that gives chord info to the Helicon Voice Live But this forces me to solely use Real Tracks. PG support says the idea of multiple MIDI drivers has been bandied about by the developers for years, but since the vast majority of users prefer Real Tracks exclusively, midi is a dinosaur.

Personally, I couldn't disagree more. From stride piano to cha cha backgrounds, I find that to this day,a mix of midi and Real....often provide the most satisfying tracks.

Perhaps someone will offer a safe, easy, and definitive workaround for achieving multiple MIDI outputs in BIAB.

And Pipeline, ....does LoopMidi actually work here without a need for midi ox to distribute the midi? If so, and if it integrates easily, please share a bit more about this. Hard to tell from your post if it actually achieves multiple MIDI without complication in BIAB. Thanks.

Top
#457228 - 02/12/18 06:54 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: axelrod]
axelrod Offline
Journeyman

Registered: 04/13/05
Posts: 401
Loc: ny
And just in csse the developers are listening, the fix for this issue seems simple..... Put 1 more entry into OUTPUT CHORDS.....a dropdown that reads
MIDI DRIVER FOR OUTPUT CHORDS


Top
#457235 - 02/12/18 07:45 PM [Band-in-a-Box for Windows] Re: Has anyone had luck with "LoopBe1" for multiple midi? [Re: axelrod]
Pipeline Offline
Veteran

Registered: 02/05/15
Posts: 2410

Top
Page 1 of 2 1 2 >


PG Music News
Get to Know The Band-in-a-Box® 2018 49-PAK for Mac

Purchase Band-in-a-Box® 2018 for Mac during our special and you will receive a Free Bonus PAK which includes Video RealTracks Set 1: Pop Ballad Band, 10 MIDI SuperTracks, 7 Instrumental Studies, 40 AmpliTube Presets & 37 Associated bonus Styles, and 52 Loops for Band-in-a-Box!

Take it a step further and add a 49-PAK to your purchase for only $49! Add the 49-PAK to your Band-in-a-Box® for Mac purchase and you'll receive these GREAT Band-in-a-Box Add-ons:
Video RealTracks Set 2: Country TrainBeat Band
ALL 40 UNRELEASED Bonus RealTracks
22 MIDI SuperTracks
101 Instrumental Studies
Artist Performance Set 8: Traditional Songs Sung by Béatrix Méthé.

Get to Know The Band-in-a-Box® 2018 49-PAK: Video link - Band-in-a-Box® 2018 for Mac- 49-PAK Overview

Band-in-a-Box® Version 2018 Pro & MegaPAK RealCombos!

We've added MORE to the RealCombos included in the Pro & MegaPAK packages with the release of Band-in-a-Box® 2018 for Mac!

The Band-in-a-Box® 2018 Pro includes 300 RealTracks instruments in over 100 bands - that's 100+ more than previous years - listen to them here.

There are now over 500 RealTracks in 300 Bands in the Band-in-a-Box® 2018 MegaPAK! Take a look at all the RealTracks & RealDrums in the MegaPAK here.

To receive the new version with these new RealCombos, upgrade during our special for as little as $59! http://www.pgmusic.com/bbmac.packages.htm.

Get ALL the Regular RealTracks & RealDrums when you upgrade to an UltraPAK or Audiophile Edition!

Title Track Day, May 23, 2018!

Did you know... today is Title Track Day!

Which album do you think of on this special day? Better yet, have you created your own album and named it after a song?

Join the converation...

New! Video RealTracks for Band-in-a-Box® 2018 for Mac!

NEW with Band-in-a-Box® 2018 for Mac - Video RealTracks Sets!

Video RealTracks allow you to see the RealTracks artist playing that track - you can use them just like any other RealTrack, and you can generate a video which will display the musician playing your song exactly as you hear it. You can also include a chord sheet or notation in the video.

We've added Video RealTracks Set 1: Pop Ballad Band to our Free Bonus PAK included in Band-in-a-Box® 2018 for Mac packages during our release special (which ends May 31st!).
Video RealTracks Set 2: Country TrainBeat Band is included in the 2018 49-PAK, along with 40 Bonus UNRELEASED RealTracks, 22 MIDI SuperTracks, 101 Instrumental Studies, and Artist Performance Set 8: Traditional Songs Sung by Béatrix Méthé.

SPECIAL OFFER: During our Band-in-a-Box® 2018 for Mac release special, purchase our "Video RealTracks Set 3-6 Special Bundle Offer" to complete your purchase with the remaining Video RealTracks Sets for the low price of just $49! http://www.pgmusic.com/bbmac.videorealtracks.htm

Learn more about the new Video RealTracks and see them in action: http://www.pgmusic.com/?vid=fzkX6jO_hW4

Video - 202 NEW RealTracks for Band-in-a-Box® 2018 for Mac!

With the release of Band-in-a-Box® 2018 for Mac we also released 202 NEW RealTracks (in Sets 278-300)!

Listen to all the individual demos here: www.pgmusic.com/bbmac.202newrealtracks.htm, or watch our Band-in-a-Box® 2018 for Mac - 202 New RealTracks Overview Video: http://www.pgmusic.com/?vid=7ZrfGSqjaOU

Get all 202 new RealTracks when you purchase any Band-in-a-Box® 2018 UltraPAK, Audiophile Edition, or the PlusPAK upgrade - on sale until May 31st!

Holiday Hours - Monday, May 21st

We're celebrating Victoria Day on Monday, May 21st. Our hours for the long weekend will be:

Customer Service:
Saturday, May 19: 7:00am - 5:00pm PST
Sunday, May 20: 8:00am - 4:00pm PST
Monday, May 21: 8:00am - 4:00pm PST

Technical Support:
Closed (will re-open Tues, May 22 at 10am PST)

Video - The Audio Chord Wizard in Band-in-a-Box® 2018 for Mac

Band-in-a-Box® 2018 for Mac boasts over 50 new features and enhancements... including the Build-in Audio Chord Wizard!

The Audio Chord Wizard has been redesigned and is now built into Band-in-a-Box®. Previously, the Audio Chord Wizard was a separate app and not tightly integrated into Band-in-a-Box®. This app is still available from the [Audio Chord Wizard] toolbar button, but the improved built-in Audio Chord Wizard can be accessed from the Audio Edit window.

Watch our latest video to learn more: Video link - Audio Chord Wizard in Band-in-a-Box® 2018 for Mac

Forum Stats
27515 Members
50 Forums
51828 Topics
428236 Posts

Max Online: 2434 @ 11/14/17 12:37 AM
Newest Members
Amexsmasterz, Aimini, hassan55, Tanna Dietrich, Korle

27515 Registered Users
Top Posters (30 Days)
Icelander 437
zedd 191
Janice & Bud 158
Noel96 146
David Snyder 141
JayO 133
HearToLearn 106
rsdean 105
Rob4580 102
Deryk - PG Music 101
Today's Birthdays
alfstone, MusicStudent, Oren Fisher, Pete b