|
Log in to post
|
Print Thread |
|
|
|
|
|
Off-Topic
|
Joined: Sep 2005
Posts: 199
Apprentice
|
OP
Apprentice
Joined: Sep 2005
Posts: 199 |
Hi all. I have a Q. re a proposed car audio install I'm in the middle of. I bought a set of ribbon tweeters some months ago to complete my revamping of the sound system in my car. I am encountering some distortion on test use, not in the tweeters but in the parent speaker I am piggy backing them off (ie. I am wiring the tweeters in parallel with the door speaker, as the car manufacturers service manual electrical digram specifies for the upmarket model of my car, which had satellite tweeters). Characteristics of the distortion are as follows: 1. Only in parent speaker, not tweeter. 2. Seems load related- sounds like clipping on musical peaks like drumbeats, bass notes at lower volumes, distortion worsens with volume and becomes more constant. 3. Occurs when crossover in place and correctly oriented. When crossover reversed, no distortion heard but tweeter non functional. 4. When crossover excluded from circuit, no distortion occurs and tweeter functions normally. Here is the link to the current version of the kit I bought. http://www.jaycar.com.au/productView.asp?URL=index&ID=CS2339&CATID=15&SUBCATID=459I have the same as these tweeters, branded "Response Precision CS 2339 ribbon tweeter", but the crossovers supplied with my kit differ. They are a small mystery circuit enclosed in black shrink wrap with sheilded wires at each end. 2 of, one per tweeter obviously. All made in China, of course. No Ohmage quoted on the box but on my multi meter they show 3.5 Ohms, and most car audio including my cars sound system is 4 Ohms. Specs quoted on the box are a freq. response of 3kHz - 40 kHz, and crossover slope of 12dB/octave. No expanded spec sheet inside (or instructions FWIW). The car head unit is a Kenwood KDC - MP5039U of ~ 22 watts RMS per corner, ~50W peak per corner. I am contemplating installing the tweeters without the crossover per 4. above. I realise it's a risk but am guessing the worst that can happen is popping the ribbons. I don't routinely listen at deafening volumes, or to very dynamic "doof doof" music, too old. Does this august company have any advice/comments? Cheers, John
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Sep 2003
Posts: 8,333
Veteran
|
|
Veteran
Joined: Sep 2003
Posts: 8,333 |
Well I'm no engineer, but Bill Cosby did some good comedy on cars. His borgenriffers were causing problems.
I'm going to have to chaw over the options for the sound system for the RV though. And I sure hope that is soon. I've started the home renos (well I hire a guy and supervise he and the wife arguing over the hue in the flooring and such.) Once I get close I'm selling my junk, my Archie Bunker chair (couldn't you guess?) and parking the RV in the driveway while we sand the floors, stage the house and flog it for what I hope is top dollar. As I don't have that mortgage thing anymore I'm buying something small, so none of my kids think of moving in. In fact maybe I'll renovate it so the main bathroom is an outhouse and the other is beside my bed.
Car audio drives me nuts. The only time I like it is if it's classical music and I have the piece sort of memorized, then I can fill in the parts killed by the passing semi hauling beer or garbage to Michigan.
I'm sure you are going to get lots of advice. I know just enough to be dangerous.
John Conley
Musica est vita
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
Quote:
No Ohmage quoted on the box but on my multi meter they show 3.5 Ohms, and most car audio including my cars sound system is 4 Ohms. Specs quoted on the box are a freq. response of 3kHz - 40 kHz, and crossover slope of 12dB/octave. No expanded spec sheet inside (or instructions FWIW).
While the DC ohmmeter check can tell you something about the impedance of a driver of any kind that has voice coils, it won't tell you that much about a Ribbon Tweeter. And, of course, can tell you nothing about the crossover. This is because of capacitance in both, which does not "pass" DC. Your audio, of course, is AC of varying frequency.
Quote:
The car head unit is a Kenwood KDC - MP5039U of ~ 22 watts RMS per corner, ~50W peak per corner.
I am contemplating installing the tweeters without the crossover per 4. above. I realise it's a risk but am guessing the worst that can happen is popping the ribbons. I don't routinely listen at deafening volumes, or to very dynamic "doof doof" music, too old.
Do NOT do that. The tweeters cannot take fullrange at ANY volume level. Without a crossover, those tweeters will not last long. Ribbon design will die even faster without a crossover, although its a moot point. The low frequencies must be blocked from reaching the tiny diaphragms of any tweeter.
John, I noticed one thing you said-- that the crossovers are using Shielded wiring. I suspect that Capacitance is rearing its ugly head here, and throwing your wideband power amplifier into distortion. This is a rather common phenomenon with Ribbon and Electrostatic tweeter systems. Quite often, the actual AC Impedance of them will drop down below 1 ohm! You can't measure that with the simple DC ohmmeter. It would take an Audio Impedance Bridge to do that. But you are in luck, for I have used the Impedance Bridges and Distortion Analyzers on the test bench many times to prove this rather commonly found situation happening with Electrostatic and Ribbon speaker systems. Sometimes the workaround is to use cheap 20 AWG gauge parallel (NOT shielded) speaker wire, about 20 feet of it for each side, coiled up. This can iron out the problem, but in a vehicle, where to put all that wire? Since your crossover already has shielded cable as part of its design, I don't think I'd even want to try that stunt, though. Shielded cable also is capacitance in and of itself, by the foot.
Not being able to put your crossovers and tweeters on the test bench (and very likely removing that shrink tubing and finding out what's really underneath...) I can't give you a reliable answer to this one that wouldn't involve trying to do things that are obviously outside your scope of reference on the subject.
You might just send these back, or write them off and find a simple set of dynamic tweeters with crossover instead.
Or -- you could purchase another smaller power amp and an electronic crossover to place between the two power amps and safely send the lows to the original amp and woofers and the highs to the new tweeter amp and ribbons.
If it was me, I'd likely go with the first choice, standard dynamic tweeters with a simple capacitive crossover. Less $$, less complexity, for about the same performance, considering it is a vehicle.
Bottom line -- This product is not performing satisfactorily for you and you should send it back.
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Aug 2000
Posts: 14,576
Veteran
|
|
Veteran
Joined: Aug 2000
Posts: 14,576 |
I think you're playing in a gas pond with matches here. I would suggest you take your car and system to a reputable radio installer and see what needs to be done.
A red flag to me is your door speakers. If these are the original speakers then you have a mis-match. If you bought all new speakers for your system then, are you sure the speakers match the freq and output of the radio's amp? Kenwood systems are great, if installed correctly.
Russ Anyday above ground is a good day Computer is Hp Pavillion Vision 6 Ghz quad core AMD processor 8 Gig memory 1 TB hard drive 6 GB hard drive Windows 7 Premium Loose nut behind the keyboard 
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Sep 2005
Posts: 199
Apprentice
|
|
OP
Apprentice
Joined: Sep 2005
Posts: 199 |
Thanks Russ, John and especially Mac.
The door and parcel shelf are indeed new Kenwood items, 6 inch 3 way in the front doors and 6 by 9 in the parcel shelf. All 4 Ohm. Head unit as stated. I am confident that the head unit and new speakers are fine for compatibilty with each other. I also constructed a subwoofer for the trunk around a Polk 8' bass driver (and powered it seperately with a dedicated power amp). No complaints with the result so far until the tweeter install of yesterday.
I did call the shop where I bought the tweeters for advice (an electronics type store, like Radio Shack) but the counter jockey was even less au fait with electronics than me. I may actually go in today and enquire further. Maybe an alternative crossover is an option.
Thanks again.
J.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Sep 2005
Posts: 199
Apprentice
|
|
OP
Apprentice
Joined: Sep 2005
Posts: 199 |
The adventure continues. I went to the auto parts store where I had bought my Polk subwoofer and spoke to Mr. Car Audio Expert. His spot diagnosis was just about spot on. He asked if the existing front door speaker that I am piggybacking signal off (in fact, wiring the ribbon tweeter parallel with) had a tweeter itself. It does- it is a Kenwood KFC - M1632A, a current model.His comment was that if it did, adding another tweeter would upset the woofer in that speaker assembly. He described the symptoms well. On paging thru a very helpful car audio site ( http://www.bcae1.com/) and examining the section on Series-Parallel Basics, it seems that although I wired in parallel to avoid halving the impedence and thus putting the head unit amp at risk, I was wrong about this principle. It looks like the connection I had made was resulting in a total 2 Ohm load. Seems I should wire in series instead. Thus the negative side of the door speaker should be connected to the positive side of the ribbon tweeter, and the negative sisde of the ribbon then sent back to the head unit. Total impedence should then be 8 Ohms as each unit is 4 Ohms. Is this correct and a safe option for extended use? Thanks, J.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
Series would be safer than parallel, which indeed would lower the impedance of the two, likely to a point below that which the amplifier is designed to operate.
Sounds like that tech has "been there, done that" -- and is speaking from experience. What he told you sounds right to me.
Just be sure that you wire the series in phase properly.
Amplifier(+) -> Main Speaker(.)+
Main SPKR(-) -->Tweeter(+)
Tweeter(-) -->Amplifier(-)
Note that in the middle there is one wire going from a minus (-) terminal to a plus (+) terminal here. Series.
If each device in this series wiring is 4 ohms as stated, then the total load would become 8 ohms at the amplifier terminals because series is addition, just add all the impedances in the series string up to arrive at the total.
It should work, but be advised that it is not what I'd call a clean arrangement in the sense that the tweeter circuit may (or may not, depending on how it's crossover is derived) affect what the woofer is getting. Hook it up and give it a listen. If it sounds good, it IS good.
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Sep 2005
Posts: 199
Apprentice
|
|
OP
Apprentice
Joined: Sep 2005
Posts: 199 |
Thanks, Mac. I found the HU's manual which states it will accept a load of b/n 4-8 Ohms. The ribbon is so small a unit that can't believe it will draw much current to work. Will give this a shot today and give you a sitrep.
John
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Sep 2005
Posts: 199
Apprentice
|
|
OP
Apprentice
Joined: Sep 2005
Posts: 199 |
Mac/others. I have wired (in series) and fired, and it sounds great so far. Adds just a sniff of crispness to the top end range which defines snare and hi hats sounds and also outlines vocal sibilants remarkably- "s" and "t" consanants particularly. No added pathlogical sounds in this configuration. Thanks all for your generous assist.
John
|
|
|
|
|
|
|
|
|
|
|
|
Ask sales and support questions about Band-in-a-Box using natural language.
ChatPG's knowledge base includes the full Band-in-a-Box User Manual and sales information from the website.
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box® 2026 for Mac - Special Offers End at 11:59pm PDT on Friday, May 15th, 2026!
Order before 11:59pm PDT on Friday, May 15th and SAVE up to 50% on most Band-in-a-Box® version 2026 for Mac Upgrade packages... and that's not all! With your version 2026 for Mac purchase, we'll include a Bonus PAK full of great new Add-ons FREE! Upgrade to the 2026 49-PAK to receive even more NEW Add-ons including 20 additional RealTracks... that's 222 NEW RealTracks available with version Band-in-a-Box® 2026 for Mac!
Upgrade to Band-in-a-Box® 2026 for Mac® today for as little as $49! Check out the Band-in-a-Box® packages page for all available purchase options.
Learn more about the Free Bonus PAK and 49-PAK here.
If you have any questions about which package is the best option for you, just let us know. We're here to help!
202 New RealTracks Released with Band-in-a-Box 2026!
With Band-in-a-Box® 2026, we've released 202 incredible new RealTracks (in sets 468-488) in a variety of genres—featuring your most requested styles!
Jazz, Funk & World (Sets 468-475):
Our new jazz, funk & blues RealTracks include a groovin’ collection of RealTracks and RealDrums! These include more requested “soul jazz” RealTracks featuring artists Neil Swainson (bass), Charles Treadway (organ), Brent Mason (guitar), and Wes Little (drums). There are new “smooth jazz” styles (4), which include a RealTracks first: muted trumpet, as well as slick new smooth jazz brushes options for drums. Blues lovers will be thrilled—there are more “classic acoustic blues” styles, including guitar (5), bass (4), and drums (10) with blues master Colin Linden, featuring understated and tasty background acoustic soloing, plus brushes drums and acoustic bass. There are also new electric blues RealTracks, including electric blues with PG favorite Johnny Hiland (3) and soulful electric slide guitar from Colin Linden (4). If you love funk & gospel, there are great new options this year, including gospel organ (3) from Charles Treadway, as well as new funk, tango, and rock ’n’ roll drums (3) and bass (1). And for big, bold arrangements, we have uptempo soul horns (4) featuring a three-part hip horn section with options for a full mix or stems of each individual horn — plus an accompanying rhythm section (4) of drums, bass, guitar, and electric piano!
Rock & Pop (Sets 476–482):
Our new rock & pop RealTracks bring a powerful mix of requested favorites, fresh genres, and modern chart-inspired styles! We have more of our popular “Producer Layered Acoustic Guitars (15)” featuring Band-in-a-Box favorite Brent Mason. We’ve continued our much-requested disco styles (10), and added new Celtic guitar (5) with a more basic, accessible approach than our previous Drop-D or DADGAD offerings. There are also highly requested yacht rock styles (17), inspired by the smooth, polished soft-rock sound of the late ’70s and early ’80s — laid-back grooves, silky electric pianos, warm textures, elegant harmonic movement, and pristine production aesthetics. Fans of heavier styles will love our new glam metal (13), capturing the flashy, high-energy sound of ’80s arena-ready guitar rock. We also have a set of rootsy modern-folk rock (18), with a warm, organic sound combining contemporary folk textures and driving acoustic strumming. And we’ve added lots of new modern pop styles (16) — the kinds of sounds you’re hearing on the radio today, featuring exciting new drums, synths, and cutting-edge RealTracks arrangements.
Country, & Americana (Sets 483–488):
Our new country & Americana RealTracks deliver a rich collection of acoustic, electric, and roots-inspired styles! We have new country pop (9) with legendary guitarist Brent Mason. There is also a potpourri (14) of bouzouki, guitars, banjo, and more, perfect for adding texture and character to contemporary acoustic arrangements. We’ve added funky country guitar (5) with PG favorite Brent Mason, along with classic pedal steel styles (5) featuring steel great Doug Jernigan. There are more country songwriter styles (8) that provide intimate, rootsy foundations for storytelling and modern Americana writing. Finally, we have “background soloing” acoustic guitar (12) with Brent Mason — simpler, but still very tasty acoustic lines designed to sit beautifully behind vocals or act as a subtle standalone solo part.
Check out all the 202 new RealTracks (in sets 468-488)!
And, if you are looking for more, the 2026 49-PAK (for $49) includes an impressive collection of 20 bonus RealTracks, featuring exciting and inspiring additions to add to your RealTracks library. You'll get new country-rhythm guitar styles from PG Music favorites Johnny Hiland and Brent Mason, along with modern-pop grooves that capture today’s radio-ready sound! There are also new indie-folk styles with guitar, bass, 6-string bass used as a high-chording instrument, acoustic guitar, and banjo. Plus, dedicated "cymbal fills" RealDrums provide an added layer that work very well with low-key folky styles with other percussion.
The 2026 49-PAK is loaded with other great new add-ons as well. Learn more about the 2026 49-PAK!
2026 Free Bonus PAK & 49-PAK for Band-in-a-Box® 2026 for Mac®!
With your version 2026 for Mac Pro, MegaPAK, UltraPAK, UltraPAK+, Audiophile Edition or PlusPAK purchase, we'll include a Bonus PAK full of great new Add-ons for FREE! Or upgrade to the 2026 49-PAK for only $49 to receive even more NEW Add-ons including 20 additional RealTracks!
These PAKs are loaded with additional add-ons to supercharge your Band-in-a-Box®!
This Free Bonus PAK includes:
- The 2026 RealCombos Booster PAK:
-For Pro customers, this includes 27 new RealTracks and 23 new RealStyles.
-For MegaPAK customers, this includes 25 new RealTracks and 23 new RealStyles.
-For UltraPAK customers, this includes 12 new RealStyles.
- MIDI Styles Set 92: Look Ma! More MIDI 15: Latin Jazz
- MIDI SuperTracks Set 46: Piano & Organ
- Instrumental Studies Set 24: Groovin' Blues Soloing
- Artist Performance Set 19: Songs with Vocals 9
- Playable RealTracks Set 5
- RealDrums Stems Set 9: Cool Brushes
- SynthMaster Sounds Set 1 (with audio demos)
- iOS Android Band-in-a-Box® App
Looking for more great add-ons, then upgrade to the 2026 49-PAK for just $49 and you'll get:
- 20 Bonus Unreleased RealTracks and RealDrums with 20 RealStyle.
- FLAC Files (lossless audio files) for the 20 Bonus Unreleased RealTracks and RealDrums
- MIDI Styles Set 93: Look Ma! More MIDI 16: SynthMaster
- MIDI SuperTracks Set 47: More SynthMaster
- Instrumental Studies 25 - Soul Jazz Guitar Soloing
- Artist Performance Set 20: Songs with Vocals 10
- RealDrums Stems Set 10: Groovin' Sticks
- SynthMaster Sounds & Styles Set 2 (sounds & styles with audio demos)
Learn more about the Bonus PAK and 49-PAK for Band-in-a-Box® 2026 for Mac®!
XPro & Xtra Styles PAK Sets On Sale Now - Until May 15, 2026!
All of our XPro Styles PAKs and Xtra Styles PAKs are on sale until May 15th, 2026!
It's the perfect time to expand your Band-in-a-Box® style library with XPro and Xtra Styles PAKs. These additional styles for Band-in-a-Box® offer a wide range of genres designed to fit seamlessly into your projects. Each style is professionally arranged and mixed, helping enhance your songs while saving you time.
What are XPro Styles and Xtra Styles PAKs?
XPro Styles PAKs are styles that work with any version (Pro, MegaPAK, UltraPAK, UltraPAK+, or Audiophile Edition) of Band-in-a-Box® 2025 (or higher). XPro Styles PAKS 1-10 includes 1,000 styles!
Xtra Styles PAKs are styles that work with the UltraPAK, UltraPAK+, or Audiophile Edition of Band-in-a-Box® 2025 (or higher). Xtra Styles PAKs 1-21 includes 3,700 styles (and 35 MIDI styles)!
The XPro & Xtra Styles PAKs are not included in any Band-in-a-Box® package.
The XPro Styles PAKs 1-10 are available for only $29 ea (reg. $49 ea), or get them all in the XPro Styles PAK Bundle for only $149 (reg. $299)! Listen to demos and order now! For Mac or for Windows.
The Xtra Styles PAKs 1-21 are available for only $29 ea (reg. $49 ea), or get them all in the Xtra Styles PAK Bundle for only $199 (reg. $349)! Listen to demos and order now! For Mac or for Windows.
Note: XPro Styles PAKs require Band-in-a-Box® 2025 or higher and are compatible with ANY package, including the Pro, MegaPAK, UltraPAK, UltraPAK+, and Audiophile Edition.
The Xtra Styles require the UltraPAK, UltraPAK+, or Audiophile Edition of Band-in-a-Box®. (Xtra Styles PAK 19 requires the 2025 or higher UltraPAK, UltraPAK+, or Audiophile Edition. They will not work with the Pro or MegaPAK version as they require the RealTracks included in the UltraPAK, UltraPAK+, or Audiophile Edition.
Supercharge your Band-in-a-Box today with XPro Styles PAKs and Xtra Styles PAK Sets!
Band-in-a-Box 2026 for Mac Videos
With the release of Band-in-a-Box® 2026 for Mac, we’re rolling out a collection of brand-new videos on our YouTube channel. We’ll keep this forum post updated so you can easily find all the latest videos in one convenient spot.
Whether you're exploring new features, checking out the latest RealTracks or Style PAKs, this is your go-to guide for Band-in-a-Box® 2026.
Check out this forum post for "One Stop Shopping" of our Band-in-a-Box® 2026 Mac Videos!
Band-in-a-Box 2026 for Mac is Here!
Band-in-a-Box® 2026 for Mac is here and it is packed with major new features! There’s a new modern look, a GUI redesign to all areas of the program including toolbars, windows, workflow and more. There’s a Multi-view layout for organizing multiple windows. A standout addition is the powerful AI-Notes feature, which uses AI neural-net technology to transcribe polyphonic audio into MIDI—entire mixes or individual instruments—making it easy to study, view, and play parts from any song. And that’s just the beginning—there are over 100 new features in this exciting release.
Along with version 2026, we've released an incredible lineup of new content! There's 202 new RealTracks, brand-new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 5, two new RealDrums Stems sets, XPro Styles PAK 10, Xtra Styles PAK 21, and much more!
Special Offers
Upgrade to Band-in-a-Box® 2026 for Mac and save up to 50% on most upgrade packages during our special offer—available until May 15, 2026. Visit our Band-in-a-Box® packages page to explore all available upgrade options.
2026 Free Bonus PAK & 49-PAK Add-ons
Our Free Bonus PAK and 49-PAK are loaded with amazing add-ons! The Free Bonus PAK is included with most Band-in-a-Box® 2026 for Mac packages, but you can unlock even more—including 20 unreleased RealTracks—by upgrading to the 2026 49-PAK for just $49.
Holiday Weekend Hours
As we hop into the Easter weekend, here are our holiday hours:
April 3 (Good Friday): 8:00 AM – 4:00 PM PDT
April 4 (Saturday): Closed
April 5 (Easter Sunday): Closed
April 6 (Easter Monday): Open regular hours
Wishing you an egg-cellent weekend!
— Team PG
|
|
|
|
|
|
|
|
|
|
|
|
Forums57
Topics86,299
Posts802,914
Members40,086
| |
Most Online64,515
Apr 8th, 2026
|
|
|
|
|
|
|
|
|
Dansk
Deutsch - Windows
Español
Français - Windows
Italiano - Windows
Nederlands
Polski
Português
Svenskt
русский
Japanese
Simplified Chinese
Traditional Chinese
Korean