First here is some reading that may help with what you are trying to do

http://bandinabox.wikia.com/wiki/Accessing_Multiple_Midi_Ports

Second, I seem to have lost the bubble on this how many outputs that you want BIAB to eventuality feed, sounds like at LEAST two? If yes then you are correct Loopbe 1 BY ITSELF won't help, (see above) – and John already said that (but stand by).

Also if yes, besides a multi-port driver you will ALSO need something like MIDI OX (you knew that right?) if trying to go DIRECT form BIAB OUT to your i Connectivity port. You COULD take BIAB OUTPUT via MIDI Yoke, Loopbe 1, or Loopbe 30 into ANOTHER DAW or standalone VSTi (that has with ability to send MIDI out) and THEN using that DAW/VSTI (as a patch bay) route its MIDI thru or OUT to your iConnectivity port.

Yes I saw you already said MIDI Yoke didn't work (more later). I have and do USE BOTH MIDI Yoke and LoopBe 30, I have and do use MIDI Yoke with a 64-bit Yamaha USB MIDI for my Montage 7 and my Fishman Triple Play (installed using its 64 bit drivers)

Like you and John said Loopbe30 has a trial, TRY IT - it won't hurt anything.


Now about MIDI Yoke:

I’m not doubting you have issues but MIDI Yoke SHOULD work fine with your iConnectivity so not sure why you are having issues??

Even if you know this I’ll mention for others who may not know . You need to route BIAB MIDI OUT to a MIDI Yoke port (#1, # 2, #3, … or #8) THEN use MIDI OX (or similar or another DAW) to connect that single MIDI Yoke port to the multiple MIDI IN’s your trying to drive. And if not using MIDI Ox you are using a a similar "software patch bay" or a DAW that can route MIDI ins to one or more MIDI outs

And if having trouble installing MIDI Yoke in Win 10

https://www.youtube.com/watch?v=kORFzILrdmA


BTW the single Loopbe1 port would work just as well in conjunction with MIDI OX as a single port of MIDI Yoke

===================
Next just me rambling

A MIDI port is a MIDI port as far as the OS (or MIDI) is concerned. Again, I use MIDI YOKE/OX with the 64-bit "drivers" for Yamaha USB support for use to/from a Montage 7 while also using my Fishman Triple Play (and its 64-bit driver) to other VSTi's and DAWS for recording/playing and routing.

The iConnectivty uses a "run of the mill" USB 2 interface (it is backward compatible to 1.1 and the whole thing peice of HW is backward compatible to Win XP SP3 - which is ONLY 32 bit)

the iConnectivty MIDI input (if designed to MIDI spec) is listening for a handshake and data from ANY MIDI input source it cannot tell if the handshake and data at its "input" was generated using 32 software, 64 bit software, or another piece of dedicated MIDI hardware, which is independent of ANY OS

The MIDI Protocol is only 8-bit; furthermore, MIDI data itself is only 7 bits since one bit is a STATUS bit (7 bits can represent 128 things)

good luck
Larry


Last edited by Larry Kehl; 02/12/18 10:06 AM.
Win10Pro,i9,64GB,2TBSSD+20TBHDDs,1080TI,BIAB'24,Scarlett18i8,Montage7,Fusion 8HD,QS8,Integra7,XV5080,QSR,SC-8850,SPLAT,FL21&others,Komp.14,IK suite&others, just a guitar player-AXE FX III &FM9T, FishmanTP, MIDIGuitar2, GK2/3'sw/GI20