|
Log in to post
|
Print Thread |
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Jul 2000
Posts: 27,364
Veteran
|
OP
Veteran
Joined: Jul 2000
Posts: 27,364 |
Really bothersome, not just recording BIAB but any audio.
It is on one channel in this example, but often occurs on the other, and often both channels.
I've sprayed the room with anti-static spray and cleaned every connection with contact cleaner. The SPDIF and optical cables, I don't know what to do with those.
Any suggestions? This is really maddening. Thanks!
mattfinley.com/promos/static.mp3
Last edited by Matt Finley; 11/10/19 05:52 AM.
BIAB 2025 Win Audiophile. Software: Studio One 7 Pro, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Presonus 192 & Faderport 8, Royer 121, Slate VSX, Adam Sub8 & Neumann 120 monitors.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Dec 2003
Posts: 24,080
Veteran
|
|
Veteran
Joined: Dec 2003
Posts: 24,080 |
We had a static noise problem when a phone got to close to a keyboard or computer. It was intermittent because the static would change or go away depending on where JonD moved while playing his keyboards.
This probably isn't your problem but I thought that I should mentioned what happened here.
PS - I have heard that Bluetooth can cause problems but since I don't have it I can't verify that.
I'm in a fitness protection program. I'm been hiding from exercise.
64 bit Win 10 Pro, the latest BiaB/RB, Roland Octa-Capture audio interface, a ton of software/hardware
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Jul 2000
Posts: 27,364
Veteran
|
|
OP
Veteran
Joined: Jul 2000
Posts: 27,364 |
Thanks, Mario.
When I shut everything down and waited, then restarted, it’s better (but not gone).
This makes me think I might have bad capacitors that fail more when heated?
Ps after isolating various parts of the system, I know the computer is not the problem. I hear the popping even when the computer is off.
BIAB 2025 Win Audiophile. Software: Studio One 7 Pro, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Presonus 192 & Faderport 8, Royer 121, Slate VSX, Adam Sub8 & Neumann 120 monitors.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Dec 2013
Posts: 2,732
Veteran
|
|
Veteran
Joined: Dec 2013
Posts: 2,732 |
Dimmer controlled lights in the room? High wattage appliances nearby? Hope you can isolate it soon.
 Steve BIAB/RB 2022, Pro Tools 2020, Korg N5, JBL LSR 4328 Powered Monitors, AKG/Shure Mics.
PC: Win11 PRO, 4 TB M2 SSD, 2 TB HD, 128 GB Memory
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Dec 2013
Posts: 2,732
Veteran
|
|
Veteran
Joined: Dec 2013
Posts: 2,732 |
After actually listening to the file, it seems like a cable(s) issue. Do you have any spare sets of cables you can try from sound interface to speakers? Maybe an issue with a power wire being too close to a speaker wire...…
Steve BIAB/RB 2022, Pro Tools 2020, Korg N5, JBL LSR 4328 Powered Monitors, AKG/Shure Mics.
PC: Win11 PRO, 4 TB M2 SSD, 2 TB HD, 128 GB Memory
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: May 2000
Posts: 22,400
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,400 |
Your signature mentions the Focusrite 18i20(2) .. I have one, and if I don't have everything set to 24 bit, when I use it I sometimes get this same problem. And by everything I mean everything in the audio chain.
Whether or not that is the case here I dunno, just mentioning; in my experience the 18i20 (2) seems pretty finicky with bitrates.
Making sure the 18i20 is fired up (before the application you are using it in is launched) seems to also be something I've noticed, so the driver can 'get control'.
I like how it works when it works, but lately I've noticed some weirdness like the info above with it.
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Jul 2000
Posts: 27,364
Veteran
|
|
OP
Veteran
Joined: Jul 2000
Posts: 27,364 |
Thank you, Steve.
No dimmers or high-wattage appliances. In fact, I have a dedicated circuit then a UPS for the studio equipment.
The static is in the sound module (Focusrite 18i20) and propagates from there. Unplugging all inputs and turning off the computer does not solve it. All the cables from the Focusrite on are digital, so I think they would either work or totally fail.
I'm starting to think it has to be failing capacitors in the Focusrite.
BIAB 2025 Win Audiophile. Software: Studio One 7 Pro, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Presonus 192 & Faderport 8, Royer 121, Slate VSX, Adam Sub8 & Neumann 120 monitors.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Jul 2000
Posts: 27,364
Veteran
|
|
OP
Veteran
Joined: Jul 2000
Posts: 27,364 |
Your signature mentions the Focusrite 18i20(2) .. I have one, and if I don't have everything set to 24 bit, when I use it I sometimes get this same problem. Whether or not that is the case here I dunno, just mentioning; in my experience, the 18i20 (2) seems pretty finicky with bitrates.
Making sure the 18i20 is fired up (before the application you are using it in is launched) seems to also be something I've noticed, so the driver can 'get control'.
I like how it works when it works, but lately I've noticed some weirdness like the info above with it. Thank you, Bob. Yes, the first thing I thought of was mismatched sample rates because you are exactly right about finicky. I think I'm good. My whole computer system is usually on so I'm pretty sure there is no 'warm up' type requirement, but I'll experiment. I run everything in the room at 44.1, 16 bit. Are you possibly suggesting the Focusrite might be more stable at 24-bit? If it helps, here is the equipment involved, pretty much in order of the signal path: i7 home-built PC (no difference when turned off), latest drivers Behringer X-Touch MIDI controller (no difference when turned off) iRig Keys 37 MIDI keyboard Roland Integra-7 hardware MIDI synth Focusrite 18i20 2nd Generation with latest driver TC Electronic Finalizer Express Presonus Central Station with remote Adam A5X monitors plus Adam subwoofer
BIAB 2025 Win Audiophile. Software: Studio One 7 Pro, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Presonus 192 & Faderport 8, Royer 121, Slate VSX, Adam Sub8 & Neumann 120 monitors.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: May 2000
Posts: 22,400
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,400 |
This may help https://support.focusrite.com/hc/en-gb/articles/207546835-Is-my-Scarlett-interface-in-16-bit-or-24-bit-on-Windows-The audio stream captured from our hardware is always 24-bit samples. These samples are not altered or processed in any way by the driver when recording. The Windows audio control panel may say the device is in 16 bit mode, but the ASIO driver bypasses the Windows audio system, and is therefore not affected by this setting.
Therefore, using 24 bit depth in your recording software, while using the ASIO driver, is still 24 bit when recording/creating, where 24 bit actually matters. To me that is kind of confusing, especially the last part. I seem to find that 'somewhere' in the signal chain the 16/24 conversion causes this and try to set everything to 24 bit. Just my experience. If you hear these clicks with no other software involved (direct monitoring) it would possibly be a cable/interference issue, but you recorded your example somehow so I have to assume some software was involved. If not, look farther upline.
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Jul 2000
Posts: 27,364
Veteran
|
|
OP
Veteran
Joined: Jul 2000
Posts: 27,364 |
Ha. I thought I understood this until I read that.  I used Adobe Audition to record the sounds in the system. That, and everything I can think of, is set to 16-bit if I have a choice. Same for the Focusrite, and of course I use the latest ASIO driver as they said. The Focusrite Control (mixing and settings) software says 44.1 but makes no mention of bit rate; I always assumed it didn't care and picked that up from the setting in the software doing the recording. I'm reasonably certain it's not sample rate (but less certain after reading the Focusrite article), and not cables as it varies from hardly happening to really bad (like my recording) and changes channels, sometimes appearing on both but usually not. Most of my cables in this part of the chain are optical or SP/DIF. And the more times I start a program (like BIAB) or Adobe Audition, the worse the clicking as if something is 'building up'. So I've resorted to turning everything off a few times during a session.
BIAB 2025 Win Audiophile. Software: Studio One 7 Pro, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Presonus 192 & Faderport 8, Royer 121, Slate VSX, Adam Sub8 & Neumann 120 monitors.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Dec 2013
Posts: 2,732
Veteran
|
|
Veteran
Joined: Dec 2013
Posts: 2,732 |
Clock settings? Check this post: Pro Tools forum link
Steve BIAB/RB 2022, Pro Tools 2020, Korg N5, JBL LSR 4328 Powered Monitors, AKG/Shure Mics.
PC: Win11 PRO, 4 TB M2 SSD, 2 TB HD, 128 GB Memory
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Jul 2000
Posts: 27,364
Veteran
|
|
OP
Veteran
Joined: Jul 2000
Posts: 27,364 |
I thought about that, Steve. I do have my Focusrite set to sync on Internal, and one of those threads suggested changing it to SP/DIF. I'll try that. Something tells me it won't sync, but I'll try again.
BIAB 2025 Win Audiophile. Software: Studio One 7 Pro, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Presonus 192 & Faderport 8, Royer 121, Slate VSX, Adam Sub8 & Neumann 120 monitors.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Jul 2000
Posts: 27,364
Veteran
|
|
OP
Veteran
Joined: Jul 2000
Posts: 27,364 |
Right, it does this weird dance of Locked, Unlocked, Locked, Unlocked etc. every second or two.
Using Internal as the clock source on the Focusrite is the only setting that works. I then tried changing the sync from Master to Slave on the Roland Integra, and the clicks continue.
But what you've shown me convinces me I'm on the right track with digital timing. Thanks, Steve.
BIAB 2025 Win Audiophile. Software: Studio One 7 Pro, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Presonus 192 & Faderport 8, Royer 121, Slate VSX, Adam Sub8 & Neumann 120 monitors.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Dec 2013
Posts: 2,732
Veteran
|
|
Veteran
Joined: Dec 2013
Posts: 2,732 |
Can you swap out the SPDIF with regular audio cables and see what you get?
Steve BIAB/RB 2022, Pro Tools 2020, Korg N5, JBL LSR 4328 Powered Monitors, AKG/Shure Mics.
PC: Win11 PRO, 4 TB M2 SSD, 2 TB HD, 128 GB Memory
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Jul 2000
Posts: 27,364
Veteran
|
|
OP
Veteran
Joined: Jul 2000
Posts: 27,364 |
Can you swap out the SPDIF with regular audio cables and see what you get? Good idea! I’ll try that. I know the sound won’t be as good - I tested this when I bought the Integra-7 - but it’s a smart diagnostic test.
BIAB 2025 Win Audiophile. Software: Studio One 7 Pro, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Presonus 192 & Faderport 8, Royer 121, Slate VSX, Adam Sub8 & Neumann 120 monitors.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Jun 2005
Posts: 7,697
Veteran
|
|
Veteran
Joined: Jun 2005
Posts: 7,697 |
If that doesn't do it you need to isolate the problem by removing parts of your system one by one.
Since this seems to point to the interface, unplug it and use your PC's internal sound chip for recording by plugging into the Line In on mobo and use headphones on the PC. That should tell you if it's the interface or not.
If not, remove and replace every single cable one by one.
If not test the speakers. Unplug them and use headphones out of the Integra.
If the noise is still there then remove the Integra, use the headphones on the interface which tests the Integra.
Then uplug everything from your UPS and plug everything direct into your wall outlets which tests the UPS.
Somewhere during this isolation testing that noise will disappear. If all that fails then take the PC to another room and test it by itself using headphones into the mobo since you've already tested everything in your studio room. That means it's something in the PC itself probably the mobo or power supply.
Bob
Biab/RB latest build, Win 11 Pro, Ryzen 5 5600 G, 512 Gig SSD, 16 Gigs Ram, Steinberg UR22 MkII, Roland Sonic Cell, Kurzweil PC3, Hammond SK1, Korg PA3XPro, Garritan JABB, Hypercanvas, Sampletank 3, more.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Jul 2000
Posts: 27,364
Veteran
|
|
OP
Veteran
Joined: Jul 2000
Posts: 27,364 |
Thanks Bob. I’ve already done most of that. As the noise is in the Focusrite it propagates forward through the other parts of the chain to the monitors, so everything after the Focusrite is Ok even though I checked it all. And I know it’s not coming from the PC as mentioned above.
Next step: write to Focusrite Support (normally quick and excellent) about the right settings between the Focusrite and the Integra.
BIAB 2025 Win Audiophile. Software: Studio One 7 Pro, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Presonus 192 & Faderport 8, Royer 121, Slate VSX, Adam Sub8 & Neumann 120 monitors.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Aug 2011
Posts: 10,933
Veteran
|
|
Veteran
Joined: Aug 2011
Posts: 10,933 |
Matt,
Have you tried bypassing the UPS? The noise might be created by an the AC to dc convertor or another electronic circuit in the UPS.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: Apr 2009
Posts: 10,673
Veteran
|
|
Veteran
Joined: Apr 2009
Posts: 10,673 |
I don't know if this is helpful, but I have a Line6 POD 2 that will throw off some noise into the system under certain circumstances. I have to be sure it's output volume is down. It is a pattern..... but yours sounded random in the clip.
Got a cell phone near the gear?
You can find my music at: www.herbhartley.comAdd nothing that adds nothing to the music. You can make excuses or you can make progress but not both. The magic you are looking for is in the work you are avoiding.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recording, Mixing, Performance and Production
|
Joined: May 2000
Posts: 22,400
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,400 |
That, and everything I can think of, is set to 16-bit if I have a choice. Same for the Focusrite, and of course I use the latest ASIO driver as they said. The Focusrite Control (mixing and settings) software says 44.1 but makes no mention of bit rate; I always assumed it didn't care and picked that up from the setting in the software doing the recording. Well Focusrite clearly states their driver is 24 bit plain and simple. Whether 44.1 or 48 or 96 or 192 doesn't matter. If I throw 16 bit at my 18i20 (2) I always have clicking. Always. Sometimes it isn't as noticeable as other times but it is there. It stinks when working on existing 16 bit content as I have to convert to 24 bit first to not have these issues .. but if everything starts in 24 bit I never have this problem. Reaper, RB .. doesn't matter which DAW, I get clicks if I send the 18i20 16 bit data. I don't recall the 2i2 doing this, but it's pretty absolute with my 18i20. I'm debating on a different interface for the studio because of it. Something with all the input connections on the front and will play nice with 16 bit. It's OK for home, but for production work I need something a little more forgiving and adaptable. Just my experience. Again, I like the unit a lot but it is pretty finicky at times. If the audio cable tests don't solve it I'd try setting your DAW to 24 bit and see if it solves things. You may have to let it convert existing stuff when you work on it, but that was the solution for me anyway. One other thing I learned is not all USB cables work the same with it. One 6' USB cable I had caused me 2 days of grief. When I first got it I didn't want the unit as close to the computer as the factory cable was forcing me to place it. I bought a nice (better quality) 15' cable and those problems went away. The 24 bit issue remained though. Are you using the factory supplied USB cable? If not, have you tried it to see if it makes a difference?
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
Ask sales and support questions about Band-in-a-Box using natural language.
ChatPG's knowledge base includes the full Band-in-a-Box User Manual and sales information from the website.
|
|
|
|
|
|
|
|
|
|
|
Season's Greetings!
Wishing everyone a happy, healthy holiday season—thanks for being part of our community!
The office will be closed for Christmas Day, but we will be back on Boxing Day (Dec 26th) at 6:00am PST.
Team PG
Band-in-a-Box 2026 Video: The Newly Designed Piano Roll Window
In this video, we explore the updated Piano Roll, complete with a modernized look and exciting new features. You’ll see new filtering options that make it easy to focus on specific note groups, smoother and more intuitive note entry and editing, and enhanced options for zooming, looping, and more.
Watch the video.
You can see all the 2026 videos on our forum!
Band-in-a-Box 2026 Video: AI Stems & Notes - split polyphonic audio into instruments and transcribe
This video demonstrates how to use the new AI-Notes feature together with the AI-Stems splitter, allowing you to select an audio file and have it separated into individual stems while transcribing each one to its own MIDI track. AI-Notes converts polyphonic audio—either full mixes or individual instruments—into MIDI that you can view in notation or play back instantly.
Watch the video.
You can see all the 2026 videos on our forum!
Bonus PAK and 49-PAK for Band-in-a-Box® 2026 for Windows®
With your version 2026 for Windows Pro, MegaPAK, UltraPAK, UltraPAK+, Audiophile Edition or PlusPAK purchase, we'll include a Bonus PAK full of great new Add-ons for FREE! Or upgrade to the 2026 49-PAK for only $49 to receive even more NEW Add-ons including 20 additional RealTracks!
These PAKs are loaded with additional add-ons to supercharge your Band-in-a-Box®!
This Free Bonus PAK includes:
- The 2026 RealCombos Booster PAK:
-For Pro customers, this includes 27 new RealTracks and 23 new RealStyles.
-For MegaPAK customers, this includes 25 new RealTracks and 23 new RealStyles.
-For UltraPAK customers, this includes 12 new RealStyles.
- MIDI Styles Set 92: Look Ma! More MIDI 15: Latin Jazz
- MIDI SuperTracks Set 46: Piano & Organ
- Instrumental Studies Set 24: Groovin' Blues Soloing
- Artist Performance Set 19: Songs with Vocals 9
- Playable RealTracks Set 5
- RealDrums Stems Set 9: Cool Brushes
- SynthMaster Sounds Set 1 (with audio demos)
- Android Band-in-a-Box® App (included)
Looking for more great add-ons, then upgrade to the 2026 49-PAK for just $49 and you'll get:
- 20 Bonus Unreleased RealTracks and RealDrums with 20 RealStyle.
- FLAC Files (lossless audio files) for the 20 Bonus Unreleased RealTracks and RealDrums
- MIDI Styles Set 93: Look Ma! More MIDI 16: SynthMaster
- MIDI SuperTracks Set 47: More SynthMaster
- Instrumental Studies 25 - Soul Jazz Guitar Soloing
- Artist Performance Set 20: Songs with Vocals 10
- RealDrums Stems Set 10: Groovin' Sticks
- SynthMaster Sounds & Styles Set 2 (sounds & styles with audio demos)
Learn more about the Bonus PAKs for Band-in-a-Box® 2026 for Windows®!
Video: New User Interface (GUI)
Join Tobin as he takes you on a tour of the new user interface in Band-in-a-Box® 2026 for Windows®! This modern GUI redesign offers a sleek new look with updated toolbars, refreshed windows, and a smoother workflow. The brand-new side toolbar puts track selection, the MultiPicker Library, and other essential tools right at your fingertips. Plus, our upgraded Multi-View lets you layer multiple windows without overlap, giving you a highly flexible workspace. Many windows—including Tracks, Piano Roll, and more—have been redesigned for improved usability and a cleaner, more intuitive interface, and more!
Watch the video.
You can see all the 2026 videos on our forum!
Introducing XPro Styles PAK 10 – Now Available for Windows Band-in-a-Box 2025 and Higher!
We've just released XPro Styles PAK 10 for Windows & Mac Band-in-a-Box version 2025 (and higher) with 100 brand new RealStyles, plus 28 RealTracks and RealDrums!
Few things are certain in life: death, taxes, and a brand spankin’ new XPro Styles PAK! In this, the 10th edition of our XPro Styles PAK series, we’ve got 100 styles coming your way! We have the classic 25 styles each from the rock & pop, jazz, and country genres, and rounding out this volume's wildcard slot is 25 styles in the Praise & Worship genre! A wide spanning genre, you can find everything from rock, folk, country, and more underneath its umbrella. The included 28 RealTracks and RealDrums can be used with any Band-in-a-Box® 2026 (and higher) package.
Here’s just a small sampling of what you can look forward to in XPro Styles PAK 10: Soft indie folk worship songs, bumpin’ country boogies, gospel praise breaks, hard rockin’ pop, funky disco grooves, smooth Latin jazz pop, bossa nova fusion, western swing, alternative hip-hop, cool country funk, and much more!
Special offers until December 31st, 2025!
All the XPro Styles PAKs 1 - 10 are on sale for only $29 ea (Reg. $49 ea), or get them all in the XPro Styles PAK Bundle for only $149 (reg. $299)! Order now!
Learn more and listen to demos of XPro Styles PAKs.
Video: XPro Styles PAK 10 Overview & Styles Demos: Watch now!
XPro Styles PAKs require Band-in-a-Box® 2025 or higher and are compatible with ANY package, including the Pro, MegaPAK, UltraPAK, UltraPAK+, and Audiophile Edition.
Introducing Xtra Styles PAK 21 – Now Available for Windows Band-in-a-Box 2025 and Higher!
Xtra Styles PAK 21 for Windows & Mac Band-in-a-Box version 2025 (and higher) is here with 200 brand new RealStyles!
We're excited to bring you our latest Xtra Styles PAK installment—the all new Xtra Styles PAK 21 for Band-in-a-Box version 2025 (and higher)!
Rejoice, one and all, for Xtra Styles PAK 21 for Band-in-a-Box® is here! We’re serving up 200 brand spankin’ new styles to delight your musical taste buds! The first three courses are the classics you’ve come to know and love, including offerings from the rock & pop, jazz, and country genres, but, not to be outdone, this year’s fourth course is bro country! A wide ranging genre, you can find everything from hip-hop, uptempo outlaw country, hard hitting rock, funk, and even electronica, all with that familiar bro country flair. The dinner bell has been rung, pickup up Xtra Styles PAK 21 today!
In this PAK you’ll discover: Energetic folk rock, raucous train beats, fast country boogies, acid jazz grooves, laid-back funky jams, a bevy of breezy jazz waltzes, calm electro funk, indie synth pop, industrial synth metal, and more bro country than could possibly fit in the back of a pickup truck!
Special offers until December 31st, 2025!
All the Xtra Styles PAKs 1 - 21 are on special for only $29 each (reg $49), or get all 21 PAKs for $199 (reg $399)! Order now!
Learn more and listen to demos of the Xtra Styles PAK 21.
Video: Xtra Styles PAK 21 Overview & Styles Demos: Watch now!
Note: The Xtra Styles require the UltraPAK, UltraPAK+, or Audiophile Edition of Band-in-a-Box®. (Xtra Styles PAK 21 requires the 2025 or higher UltraPAK, UltraPAK+, or Audiophile Edition. They will not work with the Pro or MegaPAK version because they need the RealTracks from the UltraPAK, UltraPAK+, or Audiophile Edition.
|
|
|
|
|
|
|
|
|
|
|
|
Forums57
Topics85,430
Posts791,919
Members39,884
| |
Most Online25,754
Jan 24th, 2025
|
|
|
|
|
|
|
|
|
|
|
|
There are no members with birthdays on this day. |
|
|
|
|
|
|
|
|
Dansk
Deutsch - Windows
Español
Français - Windows
Italiano - Windows
Nederlands
Polski
Português
Svenskt
русский
Japanese
Simplified Chinese
Traditional Chinese
Korean