|
Log in to post
|
Print Thread |
|
|
|
|
|
Off-Topic
|
Joined: Dec 2007
Posts: 2,445
Veteran
|
OP
Veteran
Joined: Dec 2007
Posts: 2,445 |
Hi guys,
I have a lot of old cassette tapes (some are 40+ years old) that I would like to transfer to my computer with a view to burning them to disk. I'm hoping for suggestions & advice as to which would be the most effective method of transferring; however the only cassette device I have does not have RCA outputs, only speaker outputs & a stereo headphone output. I have at my disposal:
1) Real Band
2) Goldwave
3) Cakewalk UA-1G Audio Interface
I'd appreciate any advice on which of the above would be the most suitable & effective (rather that my trying trial & error) . My preference would of course be Real Band as I can then have control over balance, bass/treble etc.
Any thoughts/advice/suggestions will be gratefully received.
Thanks in advance.
PS. Most are not commercial; (old band recordings etc) but many are from my late father who lost his ability to write, and used to send me cassette tapes rather than letters, so as you can appreciate, are very precious to me.
Thanks guys.
Cheers,
Keith
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Sep 2009
Posts: 92
Enthusiast
|
|
Enthusiast
Joined: Sep 2009
Posts: 92 |
Hi Keith this is a program I use and it works great. You get 14 days free trial and the "Full" version of the software: http://www.polderbits.com/
Dell Studio 16 Laptop i7 with 256 gig SSD
BIAB, Reaper, Encore, Sibelius
Roland SD-50
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2005
Posts: 1,992
Expert
|
|
Expert
Joined: May 2005
Posts: 1,992 |
keith.
this might work..run a test.
1. connect stereo headphone output from cass dek to ua1g line input.
(MAKE SURE YOU RECORD SOME CASSETTE NOISE BY ITSELF
FOR EXAMPLE BEFORE THE SONG STARTS.)
2. record each song in rb.
3. after recording go to town cleaning up the song as follows.
a. try the rb dx plug in NOISE GATE.
(read my tips re setting threshold...THIS IS CRITICAL.
setting the right threshold.)
and/or..
b. in RB youll also find dx plug in VINYL TOOL.
try some tests //experimentation.
and/or..
c. in goldwave is a noise reduction facility if i remember.
and/or..
d. if i remember there is a free trial of izotope available with various
restoration facilities.
i tell ya what ..as a favor to you mate.
do one song into RB , save as a wave a minutes worth of the song..
WITH CASSETTE NOISE before the song starts..or at song end.
and i'll have a bash at cleaning it up..send it back to ya..
and if your happy..i'll tell ya what i did.
then you can take it from there on all 40 songs.
i love to do audio restoration for the challenge of it.
also i lost my dad years back , and i know well the feelings in ones heart.
fair ??
god bless.
retired puter engr....powertracks on amd......NICE !
"what is the black art of audio engineering ?"
my silly songs...motagator.com/bmanning
see my tips in the tips section.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Sep 2003
Posts: 8,333
Veteran
|
|
Veteran
Joined: Sep 2003
Posts: 8,333 |
I don't know if the sell them where you are but some stores here were selling both cassette players and turntables with usb plugs.
I don't have one but wonder if a small mixer (50 buck) Behringer with a pre-amp has enough power to allow you to take it to the line in of the computer and use Audacity to record.
I also see Audacity has a new beta release. FWIW.
John Conley
Musica est vita
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Dec 2003
Posts: 24,059
Veteran
|
Veteran
Joined: Dec 2003
Posts: 24,059 |
Hi Keith, I have used Manning1’s method to preserve old band tapes. The only variations from his method and mine is that is that I used the free Audacity to clean up the noise and I added the PG Music 10 band EQ the add some treble. The real key for me was the Vinyl Tool. That is one fantastic hidden gem when restoring tapes and albums. My method is as follows:
1-record a song to a wav file
2-in Audacity remove the noise
3-in my sequencer use the Vinyl Tool to clean up the wav
4-use the 10 band EQ to polish the sound.
Good luck.
I'm in a fitness protection program. I'm been hiding from exercise.
64 bit Win 10 Pro, the latest BiaB/RB, Roland Octa-Capture audio interface, a ton of software/hardware
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jan 2006
Posts: 2,689
Veteran
|
|
Veteran
Joined: Jan 2006
Posts: 2,689 |
Hi Keith,
I just did a batch using RealBand. I can't see what the need would be to buy anything else.
Don S.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jan 2002
Posts: 10,199
Veteran
|
|
Veteran
Joined: Jan 2002
Posts: 10,199 |
Keith, Real Band, Audacity, Goldwave all will do the trick. I would, however, recommend the purchase of a better tape deck, though. Remember that these are priceless memories, and they are only going to be as good as the player that you use to record them from. An old Cassette player that has only speakers or a headphone out is not going to be the best to play back your old recordings. I would look around in your local stores and such for used decks. Also, you want to make sure the tape head is cleaned, aligned, and that the tape transport is also clean and free of debris. I would look at some higher end units on ebay, such as this one: http://cgi.ebay.com.au/Harman-Kardon-TD4...=item2a055480a9or, this one: http://cgi.ebay.com.au/YAMAHA-SINGLE-CAS...=item3caae38950or: http://cgi.ebay.com.au/Denon-DRM-510-Cas...=item439dc33f20Anyway, you get the picture. To assure the best playback, on units this old you probably should consider investing in new belts for the drive assemblies, which shouldn't be that hard to replace. I think with that, you'll be very pleased with the results you get from transferring your tapes to digital. Gary
I'm blessed watching God do what He does best. I've had a few rough years, and I'm still not back to where I want to be, but I'm on the way and things are looking far better now than what they were!
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2000
Posts: 22,393
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,393 |
As Gary said, you may want to buy/borrow another deck.
Do NOT hook the speaker output of the deck you have to the line level inputs of any device. You may be able to (carefully) use the headphone out, adjusting the volume slowly up from zero to set the levels.
Having a line level out will likely make your job easier and better.
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jul 2003
Posts: 267
Apprentice
|
|
Apprentice
Joined: Jul 2003
Posts: 267 |
I take the headphone out into the rca in jacks on my mixer, then record the output via Audacity. The advantage of that is that I can adjust the mixer to get the best sound before I actually record the output.
tony
Lenovo lappie, 4Gb RAM, 500Gb HD
Ubuntu 12.04
Running BIAB under WINE
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Dec 2007
Posts: 2,445
Veteran
|
|
OP
Veteran
Joined: Dec 2007
Posts: 2,445 |
Hi guys,
Thank you all for the excellent advice & suggestions: they will all be taken on board. The tape transferring is going to be one of my winter projects, so I'll be trying the various options you suggested.
Thanks again.
Cheers,
Keith
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jul 2000
Posts: 1,696
Expert
|
|
Expert
Joined: Jul 2000
Posts: 1,696 |
One more word or two - you will notice that you will probably lose oxide from the tape which will coat the heads and create it's own noise and cause the tape speed to slow. Clean the heads after using them for a short period of time. When I transferred my analogue stuff, I cleaned after each song until I figured out just how fast the tape was losing oxide and it was accumulating on the heads. Then cleaned accordingly. I was also fortunate enough to find a double Sony cassette player c 1995 vintage on a buy and sell list. It worked superbly for the playback - easy access for cleaning.
Enjoy the memories. Ian
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jun 2006
Posts: 7,258
Veteran
|
|
Veteran
Joined: Jun 2006
Posts: 7,258 |
Keith, I've used adobe audition for years and find it brilliant for removing noise. If you can pick up a copy 2nd hand it'll be worth it, some of the older versions are every bit as good.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Dec 2007
Posts: 2,445
Veteran
|
|
OP
Veteran
Joined: Dec 2007
Posts: 2,445 |
Thanks Ian & Graham. What do you suggest is the best thing to clean the tape heads with?
Cheers,
Keith
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jan 2002
Posts: 10,199
Veteran
|
|
Veteran
Joined: Jan 2002
Posts: 10,199 |
Keith,
Rubbing alcohol and a swab.
Also, make sure that you get the rollers and pinch rollers as well. Do not put the tape in until everything is dry.
Many cassette decks will allow you to remove part of the front cover so you can close the door and activate the play mechanism to move the tape head, rollers and pinch rollers into position. It may not run for long, if there is an auto stop mechanism, but it should be enough, if you do it a few times, to get stuff cleaned.
Also, look for a tape head demagnetizer. The heads become magnetized over time, reducing high frequency playback. Use of a demagnetizer will restore the head to it's designed condition, giving you the best possible playback.
Gary
I'm blessed watching God do what He does best. I've had a few rough years, and I'm still not back to where I want to be, but I'm on the way and things are looking far better now than what they were!
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jul 2000
Posts: 1,696
Expert
|
|
Expert
Joined: Jul 2000
Posts: 1,696 |
You'll probably start to notice a brownish discoloration on the pinch roll but I'd still do the heads every two songs or equivalent. At one point I tried to play back the Gambler album when it got old and the tape just slowed it down to a stop. Just depends on the quality used in cassettes by the company. My old quarter in large reels have held up better that the cassettes over the years - never know, but it's fun recovering the old stuff - worth the effort. P.S. don't turn the demag on near any tape.   Cheers - Ian
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
Quote:
however the only cassette device I have does not have RCA outputs, only speaker outputs & a stereo headphone output. ....
More than a software suggestion, you first need a quality cassette deck.
Beg, Borrow, get your hands on one to do the task.
**Examine the tape heads for cleanliness, scratches, etc. Do not use a scratched head of any kind on your precious tapes. One pass can ruin the tape permanently. Also examine the rubber pinch roller(s) and don't use any deck that has shiny, mirrored or "barrelled" worn pinch rollers, a recipe for not only bad audio in the wow and flutter dept. but a situation that can also result in the dreaded "eaten" cassette tape as the tape skews off of the barrelled worn pinch roller. Rubber pinch roller should be square to the capstan, in other words, *flat*.
**CLEAN the heads, tape path to include rubber pinch rollers w/alcohol and cotton swabs before *every* playback. Oxide buildup on the heads and tape path is not good for the next tape recording. Cleanliness is indeed next to Godliness when it comes to working with analog tape. Allow the path to dry thoroughly before attempting to run a precious tape through there. Only takes a couple or three minutes for that.
**Also get a tape path demagnetizing tool and use it on the deck's heads and capstan, tape guide path, before every session.
**First thing to do when you pop a Cassette in the deck is to FF it all the way to one end and then Rewind it all the way back. This is to put all the windings at the same tension as the deck operates. Can eliminate tape tension wow and flutter problems before they can rear their ugly little heads on your final recording. This should be done when recording any reel-based media, is especially important on tapes that have been sitting around in storage, for over time the tape windings can bind to each other, not a good thing when the transport is supposed to be moving the tape at an even speed across the tape head(s).
**fIND OUT IF THE TAPE WAS RECORDED USING DOLBY NOISE REDUCTION, AND IF SO, WHICH TYPE. Failure to play back using the same type of Dolby Noise Reduction will result in skewed EQ of the original recording. The same goes for tapes made with Ferrous-based, or Chromium-based, etc. and if you have those, the deck used should have the switch for the proper EQ curve of the various tape formats.
**LISTEN FIRST TO THE RAW DIGITAL RECORDING. Don't just blanket apply any noise reduction algo or anything else digital unless and until you have listened carefully to the raw digital recording and ascertained what's *wrong* with it. There may be little need to do anything at all here, maybe some tapes will sound good "as-is" while others not so good, etc. Make *decisions* rather than invoke some blanket set of algorithms to the entire batch.
But your hurdle to cross first is that cassette deck issue.
Get your hands on a rather decent one for the purpose, don't waste your precious time with a sub-par cassette deck -- and if it has only headphone jack output, it is very likely to be sub-par for this purpose.
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Mar 2006
Posts: 812
Expert
|
|
Expert
Joined: Mar 2006
Posts: 812 |
Mac, that is one of the most helpful post's I've seen here on the PG forums. I have a client at the moment who is trying to do this and I'm going to make sure he reads your post.
Thanks so much!
Ed
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Aug 2008
Posts: 301
Journeyman
|
|
Journeyman
Joined: Aug 2008
Posts: 301 |
Hi Keith,
In addition to all the above good advice,the way to extract the best sound from a cassette is to use a deck that lets you adjust the azimuth of the playback head. Unless you get lucky and find a deck that just happens to be perfectly aligned to your cassettes, you're going to lose some high-frequency content because of the misalignment. That said, it can be tricky but well worth the effort if you're comfortable with having a go. The tiniest of adjustments is all that will be required.
I wouldn't recommend this if you were going to use the deck for subsequent recording but I've found it to be invaluable for ensuring your high's aren't lost during playback of cassettes from different machines. Of course, in an ideal world all decks would be calibrated the same but even high end machines are not immune to a little azimuth shift!
Kind Regards,
Dave.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
Quote:
Hi Keith,
In addition to all the above good advice,the way to extract the best sound from a cassette is to use a deck that lets you adjust the azimuth of the playback head.
*All* decks have a head azimuth alignment adjustment screw. At least all that are any good do.
Easy to tweak one, get the right sized jeweler's screwdriver, first *demagnetize* it, then while the cassette is playing back *in the center of the tape travel, not from either end* adjust that screw in either diretion while listening to the high frequency content. Sometimes helps to boost the treble control of your listening system temporarily so that you can hear this. Point where there is most treble content heard is the best place to leave the adjustment.
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Dec 2007
Posts: 2,445
Veteran
|
|
OP
Veteran
Joined: Dec 2007
Posts: 2,445 |
Thanks for all the great advice & information, guys. I'll start searching for a tape deck, and beg, borrow or buy. I'll let you know how I get along.
Cheers,
Keith
|
|
|
|
|
|
|
|
|
|
|
|
Ask sales and support questions about Band-in-a-Box using natural language.
ChatPG's knowledge base includes the full Band-in-a-Box User Manual and sales information from the website.
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box 2026 Video: The Newly Designed Piano Roll Window
In this video, we explore the updated Piano Roll, complete with a modernized look and exciting new features. You’ll see new filtering options that make it easy to focus on specific note groups, smoother and more intuitive note entry and editing, and enhanced options for zooming, looping, and more.
Watch the video.
You can see all the 2026 videos on our forum!
Band-in-a-Box 2026 Video: AI Stems & Notes - split polyphonic audio into instruments and transcribe
This video demonstrates how to use the new AI-Notes feature together with the AI-Stems splitter, allowing you to select an audio file and have it separated into individual stems while transcribing each one to its own MIDI track. AI-Notes converts polyphonic audio—either full mixes or individual instruments—into MIDI that you can view in notation or play back instantly.
Watch the video.
You can see all the 2026 videos on our forum!
Bonus PAK and 49-PAK for Band-in-a-Box® 2026 for Windows®
With your version 2026 for Windows Pro, MegaPAK, UltraPAK, UltraPAK+, Audiophile Edition or PlusPAK purchase, we'll include a Bonus PAK full of great new Add-ons for FREE! Or upgrade to the 2026 49-PAK for only $49 to receive even more NEW Add-ons including 20 additional RealTracks!
These PAKs are loaded with additional add-ons to supercharge your Band-in-a-Box®!
This Free Bonus PAK includes:
- The 2026 RealCombos Booster PAK:
-For Pro customers, this includes 27 new RealTracks and 23 new RealStyles.
-For MegaPAK customers, this includes 25 new RealTracks and 23 new RealStyles.
-For UltraPAK customers, this includes 12 new RealStyles.
- MIDI Styles Set 92: Look Ma! More MIDI 15: Latin Jazz
- MIDI SuperTracks Set 46: Piano & Organ
- Instrumental Studies Set 24: Groovin' Blues Soloing
- Artist Performance Set 19: Songs with Vocals 9
- Playable RealTracks Set 5
- RealDrums Stems Set 9: Cool Brushes
- SynthMaster Sounds Set 1 (with audio demos)
- Android Band-in-a-Box® App (included)
Looking for more great add-ons, then upgrade to the 2026 49-PAK for just $49 and you'll get:
- 20 Bonus Unreleased RealTracks and RealDrums with 20 RealStyle.
- FLAC Files (lossless audio files) for the 20 Bonus Unreleased RealTracks and RealDrums
- MIDI Styles Set 93: Look Ma! More MIDI 16: SynthMaster
- MIDI SuperTracks Set 47: More SynthMaster
- Instrumental Studies 25 - Soul Jazz Guitar Soloing
- Artist Performance Set 20: Songs with Vocals 10
- RealDrums Stems Set 10: Groovin' Sticks
- SynthMaster Sounds & Styles Set 2 (sounds & styles with audio demos)
Learn more about the Bonus PAKs for Band-in-a-Box® 2026 for Windows®!
Video: New User Interface (GUI)
Join Tobin as he takes you on a tour of the new user interface in Band-in-a-Box® 2026 for Windows®! This modern GUI redesign offers a sleek new look with updated toolbars, refreshed windows, and a smoother workflow. The brand-new side toolbar puts track selection, the MultiPicker Library, and other essential tools right at your fingertips. Plus, our upgraded Multi-View lets you layer multiple windows without overlap, giving you a highly flexible workspace. Many windows—including Tracks, Piano Roll, and more—have been redesigned for improved usability and a cleaner, more intuitive interface, and more!
Watch the video.
You can see all the 2026 videos on our forum!
Introducing XPro Styles PAK 10 – Now Available for Windows Band-in-a-Box 2025 and Higher!
We've just released XPro Styles PAK 10 for Windows & Mac Band-in-a-Box version 2025 (and higher) with 100 brand new RealStyles, plus 28 RealTracks and RealDrums!
Few things are certain in life: death, taxes, and a brand spankin’ new XPro Styles PAK! In this, the 10th edition of our XPro Styles PAK series, we’ve got 100 styles coming your way! We have the classic 25 styles each from the rock & pop, jazz, and country genres, and rounding out this volume's wildcard slot is 25 styles in the Praise & Worship genre! A wide spanning genre, you can find everything from rock, folk, country, and more underneath its umbrella. The included 28 RealTracks and RealDrums can be used with any Band-in-a-Box® 2026 (and higher) package.
Here’s just a small sampling of what you can look forward to in XPro Styles PAK 10: Soft indie folk worship songs, bumpin’ country boogies, gospel praise breaks, hard rockin’ pop, funky disco grooves, smooth Latin jazz pop, bossa nova fusion, western swing, alternative hip-hop, cool country funk, and much more!
Special offers until December 31st, 2025!
All the XPro Styles PAKs 1 - 10 are on sale for only $29 ea (Reg. $49 ea), or get them all in the XPro Styles PAK Bundle for only $149 (reg. $299)! Order now!
Learn more and listen to demos of XPro Styles PAKs.
Video: XPro Styles PAK 10 Overview & Styles Demos: Watch now!
XPro Styles PAKs require Band-in-a-Box® 2025 or higher and are compatible with ANY package, including the Pro, MegaPAK, UltraPAK, UltraPAK+, and Audiophile Edition.
Introducing Xtra Styles PAK 21 – Now Available for Windows Band-in-a-Box 2025 and Higher!
Xtra Styles PAK 21 for Windows & Mac Band-in-a-Box version 2025 (and higher) is here with 200 brand new RealStyles!
We're excited to bring you our latest Xtra Styles PAK installment—the all new Xtra Styles PAK 21 for Band-in-a-Box version 2025 (and higher)!
Rejoice, one and all, for Xtra Styles PAK 21 for Band-in-a-Box® is here! We’re serving up 200 brand spankin’ new styles to delight your musical taste buds! The first three courses are the classics you’ve come to know and love, including offerings from the rock & pop, jazz, and country genres, but, not to be outdone, this year’s fourth course is bro country! A wide ranging genre, you can find everything from hip-hop, uptempo outlaw country, hard hitting rock, funk, and even electronica, all with that familiar bro country flair. The dinner bell has been rung, pickup up Xtra Styles PAK 21 today!
In this PAK you’ll discover: Energetic folk rock, raucous train beats, fast country boogies, acid jazz grooves, laid-back funky jams, a bevy of breezy jazz waltzes, calm electro funk, indie synth pop, industrial synth metal, and more bro country than could possibly fit in the back of a pickup truck!
Special offers until December 31st, 2025!
All the Xtra Styles PAKs 1 - 21 are on special for only $29 each (reg $49), or get all 21 PAKs for $199 (reg $399)! Order now!
Learn more and listen to demos of the Xtra Styles PAK 21.
Video: Xtra Styles PAK 21 Overview & Styles Demos: Watch now!
Note: The Xtra Styles require the UltraPAK, UltraPAK+, or Audiophile Edition of Band-in-a-Box®. (Xtra Styles PAK 21 requires the 2025 or higher UltraPAK, UltraPAK+, or Audiophile Edition. They will not work with the Pro or MegaPAK version because they need the RealTracks from the UltraPAK, UltraPAK+, or Audiophile Edition.
Introducing XPro Styles PAK 10 – Now Available for Mac Band-in-a-Box 2025 and Higher!
We've just released XPro Styles PAK 10 for Mac & Windows Band-in-a-Box version 2025 (and higher) with 100 brand new RealStyles, plus 28 RealTracks and RealDrums!
Few things are certain in life: death, taxes, and a brand spankin’ new XPro Styles PAK! In this, the 10th edition of our XPro Styles PAK series, we’ve got 100 styles coming your way! We have the classic 25 styles each from the rock & pop, jazz, and country genres, and rounding out this volume's wildcard slot is 25 styles in the Praise & Worship genre! A wide spanning genre, you can find everything from rock, folk, country, and more underneath its umbrella. The included 28 RealTracks and RealDrums can be used with any Band-in-a-Box® 2026 (and higher) package.
Here’s just a small sampling of what you can look forward to in XPro Styles PAK 10: Soft indie folk worship songs, bumpin’ country boogies, gospel praise breaks, hard rockin’ pop, funky disco grooves, smooth Latin jazz pop, bossa nova fusion, western swing, alternative hip-hop, cool country funk, and much more!
Special offers until December 31st, 2025!
All the XPro Styles PAKs 1 - 10 are on sale for only $29 ea (Reg. $49 ea), or get them all in the XPro Styles PAK Bundle for only $149 (reg. $299)! Order now!
Learn more and listen to demos of XPro Styles PAKs.
Video: XPro Styles PAK 10 Overview & Styles Demos: Watch now!
XPro Styles PAKs require Band-in-a-Box® 2025 or higher and are compatible with ANY package, including the Pro, MegaPAK, UltraPAK, UltraPAK+, and Audiophile Edition.
|
|
|
|
|
|
|
|
|
|
|
|
Forums57
Topics85,389
Posts791,533
Members39,873
| |
Most Online25,754
Jan 24th, 2025
|
|
|
|
|
|
|
|
|
Dansk
Deutsch - Windows
Español
Français - Windows
Italiano - Windows
Nederlands
Polski
Português
Svenskt
русский
Japanese
Simplified Chinese
Traditional Chinese
Korean