|
Log in to post
|
Print Thread |
|
|
|
|
|
Off-Topic
|
|
eddie1261
Unregistered
|
|
eddie1261
Unregistered
|
As my aftermarket knee proves, this topic applies to both instruments and people, so this should cover a lot of ground. Here in Ohio we have almost NO place to take in a knob to find a replacement because you lost 2 of the other knobs. Radio Shack, and Olsen's way back, were the go to places, but Radio Shack is gone. Plus, how do I order knobs online? I don't know what to measure and how to describe what I need to some clerk on the phone that was not yet born when the Korg KMX-62 rack mount mixer was made that needs 7 new knobs because not only is one missing completely, the rest of them (6 channels and a master volume) are missing the little center disc that has the index mark on them. I have zero idea how I am going to find knobs. This mixer is from 1988. And funny story, I bought it in 1988. In 2017 I used it (and the matching EQ) as trade collateral for a case that was the right case for my Applause acoustic. That guitar and case went to the same local shop for resale, and when it was sold I got enough money for them that allowed me to buy the rack pieces back from the guy and get a used 6 space rack in the deal. I can't even wrap my head around if that was win, lose or draw on that deal that spanned 4 years. Radio Shack, how I miss thee.... There used to be one every 37 feet. Now the places that have a Radio Shack signs just have a handful of stuff with their labels. AND there's no guarantee they ever had this exact knob. Where's Billy at? He's a builder! Where do I buy parts and what do I have to measure? Guess what I am doing tomorrow? Going to places to get suggestions where to look for these knobs. It may be as simple as asking the people where I am taking the mixer to get the stereo pot that snapped off WAY back when replaced. Thanks, roadies... 
Last edited by eddie1261; 07/25/21 11:18 AM.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Aug 2011
Posts: 11,015
Veteran
|
Veteran
Joined: Aug 2011
Posts: 11,015 |
Check e-Bay for a "parts only" donor mixer or replacement knobs from someone parting one out. If you have at least one knob, measure the inside diameter where the shaft goes, the diameter and height. Then search online for a knob with similar dimensions. The shaft dimension is the biggie as it may be metric (likely) or SAE (unlikely). But try to force a knob with the wrong internal diameter will either cause damage to the shaft or you won't be able to tighten the knob. Most knobs are press on, not held on with a set screw. Shafts may have a spline to them or split. Press on knobs work real well with spline shafts. Believe it or not, you may be able to find generic knobs that will fit from the hardware section of Lowes Hardware or Home Depot. Online search at +++ Digikey +++ , +++ Stewart Mac +++ , +++ AllParts.com +++ , +++ AliExpress +++ , +++ Amazon +++ . While you may not find the exact knobs you may find replacement knobs that work as well, or look even better, then the original.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
|
eddie1261
Unregistered
|
|
eddie1261
Unregistered
|
These are spline shaft knobs. I think an early stop will be at Home Depot where I will "demo" a micrometer so I can measure the ID of the knob. The thing about this is that picture shows a "center" knob that slides down onto the spline and seats onto a second knob because the back control is for the effects return. Here's a look. Stereo!  
Last edited by eddie1261; 07/25/21 01:23 PM.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jul 2015
Posts: 2,741
Veteran
|
|
Veteran
Joined: Jul 2015
Posts: 2,741 |
Actually Eddie, a competent electronics person would be able to provide you with what you need if it exist. He would need Make, model, a serial number. He then may be able to find a schematic and perhaps a parts list. I would likely find the item from CE Distribution, DigiKey or Mouser electronics. Perhaps on ebay also. Ebay may sell the whole unit as parts which is where really hard to find items often come from. (the Cheap answer) Two or three places in Europe collect hard to find items and sell for large amounts of money. So do a few other electronics places but they would be unlikely to take your call if they don't know you. (expensive) Then their are electronic/ mechanical engineer types who have the equipment to make a new one. I can make you a knob in any material with gold or silver or any type of plating to include amorphous diamond carbon using a high vacuum gas plasma reactor. ( only if you are Elon's brother with plenty of $$$) Home Depot?....good luck on that Now...lets get back to your issue. If you don't need everything to match and only function, try ebay first. They sell assortments of knobs. The sell push pull pots. I most likely have everything you need but I have to have the defective parts in my hand and Make, model and serial number of the unit. Some internal photos would help. Billy EDIT: The tool to measure with...$20 at Harbor Freight 
Last edited by Planobilly; 07/25/21 03:11 PM.
“Amazing! I’ll be working with Jaco Pastorius, Charlie Parker, Art Tatum, and Buddy Rich, and you’re telling me it’s not that great of a gig?
“Well…” Saint Peter, hesitated, “God’s got this girlfriend who thinks she can sing…”
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
|
eddie1261
Unregistered
|
|
eddie1261
Unregistered
|
Billy, the broken pot will get handled by my guy. I just need knobs that have the small center insert that has the index markings. Purely cosmetics. If my guy (Jim) can source them, I will happily et him! I'll see him tomorrow. If I have to source them I need to go to a DIY store and "test" a micrometer so I know the diameter of the hole in the knob.
The broken pot in the picture isn't push push. It's just a stereo pot and the inside ring goes to the effects bus. A roadie snapped it off one night putting my rack away.
And he lived!!!
Last edited by eddie1261; 07/25/21 03:14 PM.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jul 2015
Posts: 2,741
Veteran
|
|
Veteran
Joined: Jul 2015
Posts: 2,741 |
Finding a knob "may" be a problem. There are two or three ways to solve the pot issue.
This knob controls two separate functions, VOL and Effect.
So I read what you said again and I assume the knob is split and the outside part holds the inside part on.
Billy
“Amazing! I’ll be working with Jaco Pastorius, Charlie Parker, Art Tatum, and Buddy Rich, and you’re telling me it’s not that great of a gig?
“Well…” Saint Peter, hesitated, “God’s got this girlfriend who thinks she can sing…”
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
|
eddie1261
Unregistered
|
|
eddie1261
Unregistered
|
That is close. The bigger piece slips tightly on the erect return ring. It will stay on without the center knob. Worst case is that I only find the slimmer center knob and I don't use the effects loop anyway. I'll know more Monday morning.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Oct 2017
Posts: 745
Journeyman
|
|
Journeyman
Joined: Oct 2017
Posts: 745 |
My gut response would be to check with a place that sells ham radio equipment. Or a ham...
There is a lot of old radio equipment out there and hams save pieces and parts.
...Deb
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jun 2003
Posts: 1,116
Expert
|
|
Expert
Joined: Jun 2003
Posts: 1,116 |
These days, any geek with a 3D printer can make you a replacement knob for old equipment.
Keith
2026 Audiophile Windows 11 RYZEN THREADRIPPER 3960X 4.5GHZ 128 GB RAM 2 Nvidia RTX 3090s, Vegas,Acid,SoundForge,Izotope Production,Melodyne Studio,SONAR,3 Raven Mtis
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jul 2000
Posts: 6,493
Veteran
|
|
Veteran
Joined: Jul 2000
Posts: 6,493 |
I miss Radio Shack and also Mom & Pop music stores.
People started buying from Internet, Mail-Order, and Big Box stores to save a few pennies, and the expert people we used to depend on went out of business.
We did this to ourselves.
Good luck with your knob quest.
Notes
Bob "Notes" Norton  Norton Music
https://www.nortonmusic.com
100% MIDI Super-Styles recorded by live, pro, studio musicians for a live groove
& Fake Disks for MIDI and/or RealTracks
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Oct 2000
Posts: 720
Journeyman
|
|
Journeyman
Joined: Oct 2000
Posts: 720 |
You might find a generic Dual Concentric Control Knob that will work. Here's an example: Dual Concentric Knobs on Reverb.Com -rob
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
|
eddie1261
Unregistered
|
|
eddie1261
Unregistered
|
My guy has the mixer now and he said he probably has knobs laying around.
Does everybody have "a guy" like how everybody says their doctor is "the best"? "You gotta go to my guy. He's the best!"
I'll never forget the joke "What do you call a guy who finishes last in his class in med school?"
"Doctor..."
Worst case I told him that f he had to order them to do so. He can measure the shaft sizes and stuff.
Last edited by eddie1261; 07/26/21 05:21 AM.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Nov 2009
Posts: 1,413
Expert
|
|
Expert
Joined: Nov 2009
Posts: 1,413 |
Bandcamp Win-11; BiaB-2026 Audiophile (latest version)
Cakewalk Sonar; Melodyne-5; Scaler 3; NI Komplete:
Focusrite Scarlett 18i20
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Apr 2009
Posts: 10,808
Veteran
|
|
Veteran
Joined: Apr 2009
Posts: 10,808 |
These are spline shaft knobs. I think an early stop will be at Home Depot where I will "demo" a micrometer so I can measure the ID of the knob. The thing about this is that picture shows a "center" knob that slides down onto the spline and seats onto a second knob because the back control is for the effects return. Here's a look. Stereo! Man if you gotta use a pipe wrench to turn the knobs maybe it's time to put some lubricant on them.... I broke a tuning peg on my very first guitar doing that very thing.... some grease would help. But yeah...Amazon or Ebay will get you there.
You can find my music at: www.herbhartley.comAdd nothing that adds nothing to the music. You can make excuses or you can make progress but not both. The magic you are looking for is in the work you are avoiding.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
|
eddie1261
Unregistered
|
|
eddie1261
Unregistered
|
LOL @Herb's comment!
The top picture is actually one that HAS a knob! It's just that I bought that mixer in like 1988. The second pic is the one the roadie hit on the end of the stage and snapped channel 4 off. The knobs are on the end of the broken spline in a bar somewhere in Canada.
|
|
|
|
|
|
|
|
|
|
|
|
Ask sales and support questions about Band-in-a-Box using natural language.
ChatPG's knowledge base includes the full Band-in-a-Box User Manual and sales information from the website.
|
|
|
|
|
|
|
|
|
|
|
Update to Build 10 of RealBand® 2026 for Windows®!
If you're already using RealBand 2026 for Windows, download build 10 to get all the latest additions and enhancements.
Band-in-a-Box® 2025 for Mac® users: Build 904 now available!
If you're already using Band-in-a-Box® 2025 for Mac®, make sure to grab the latest update! Build 904 is now available for download and includes the newest additions and enhancements from our team.
Band-in-a-Box® 2026 for Windows® users: Build 1237 is now available!
Already a Band-in-a-Box 2026 for Windows user? Stay up to date and download the build 1237 to get all the latest additions and enhancements.
PowerTracks Pro 2026 for Windows is Here!
PowerTracks 2026 is here—bringing powerful new enhancements designed to make your production workflow faster, smoother, and more intuitive than ever.
The enhanced Mixer now shows Track Type and Instrument icons for instant track recognition, while a new grid option simplifies editing views. Non-floating windows adopt a modern title bar style, replacing the legacy blue bar.
The Master Volume is now applied at the end of the audio chain for consistent levels and full-signal master effects.
Tablature now includes a “Save bends when saving XML” option for improved compatibility with PG Music tools. Plus, you can instantly match all track heights with a simple Ctrl-release after resizing, and Add2 chords from MGU/SGU files are now fully supported... and more!
Get started today—first-time packages start at just $49.
Already using PowerTracks Pro Audio? Upgrade for as little as $29 and enjoy the latest improvements!
Order now!
Band-in-a-Box 2026 for Windows Special Offers End Tomorrow (January 15th, 2026) at 11:59 PM PST!
Time really is running out! Save up to 50% on Band-in-a-Box® 2026 for Windows® upgrades and receive a FREE Bonus PAK—only when you order by 11:59 PM PST on Thursday, January 15, 2026!
We've added many major new features and new content in a redesigned Band-in-a-Box® 2026 for Windows®!
Version 2026 introduces a modernized GUI redesign across the program, with updated toolbars, refreshed windows, smoother workflows, and a new Dark Mode option. There’s also a new side toolbar for quicker access to commonly used windows, and the new Multi-View feature lets you arrange multiple windows as layered panels without overlap, making it easier to customize your workspace.
Another exciting new addition is the new AI-Notes feature, which can transcribe polyphonic audio into MIDI. You can view the results in notation or play them back as MIDI, and choose whether to process an entire track or focus on specific parts like drums, bass, guitars/piano, or vocals. There's over 100 new features in Band-in-a-Box® 2026 for Windows®.
There's an amazing collection of new content too, including 202 RealTracks, new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 5, two RealDrums Stems sets, XPro Styles PAK 10, Xtra Styles PAK 21, and much more!
Upgrade your Band-in-a-Box for Windows to save up to 50% on most Band-in-a-Box® 2026 upgrade packages!
Plus, when you order your Band-in-a-Box® 2026 upgrade during our special, you'll receive a Free Bonus PAK of exciting new add-ons.
If you need any help deciding which package is the best option for you, just let us know. We are here to help!
Band-in-a-Box® 2026 for Windows® Special Offers Extended Until January 15, 2026!
Good news! You still have time to upgrade to the latest version of Band-in-a-Box® for Windows® and save. Our Band-in-a-Box® 2026 for Windows® special now runs through January 15, 2025!
We've packed Band-in-a-Box® 2026 with major new features, enhancements, and an incredible lineup of new content! The program now sports a sleek, modern GUI redesign across the entire interface, including updated toolbars, refreshed windows, smoother workflows, a new dark mode option, and more. The brand-new side toolbar provides quicker access to key windows, while the new Multi-View feature lets you arrange multiple windows as layered panels without overlap, creating a flexible, clutter-free workspace. We have an amazing new “AI-Notes” feature. This transcribes polyphonic audio into MIDI so you can view it in notation or play it back as MIDI. You can process an entire track (all pitched instruments and drums) or focus on individual parts like drums, bass, guitars/piano, or vocals. There's an amazing collection of new content too, including 202 RealTracks, new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 5, two RealDrums Stems sets, XPro Styles PAK 10, Xtra Styles PAK 21, and much more!
There are over 100 new features in Band-in-a-Box® 2026 for Windows®.
When you order purchase Band-in-a-Box® 2026 before 11:59 PM PST on January 15th, you'll also receive a Free Bonus PAK packed with exciting new add-ons.
Upgrade to Band-in-a-Box® 2026 for Windows® today! Check out the Band-in-a-Box® packages page for all the purchase options available.
Happy New Year!
Thank you for being part of the Band-in-a-Box® community.
Wishing you and yours a very happy 2026—Happy New Year from all of us at PG Music!
|
|
|
|
|
|
|
|
|
|
|
|
Forums57
Topics86,084
Posts799,890
Members40,031
| |
Most Online44,367
Mar 4th, 2026
|
|
|
|
|
|
|
|
|
|
|
|
There are no members with birthdays on this day. |
|
|
|
|
|
|
|
|
Dansk
Deutsch - Windows
Español
Français - Windows
Italiano - Windows
Nederlands
Polski
Português
Svenskt
русский
Japanese
Simplified Chinese
Traditional Chinese
Korean