Hello Folk,I moved houses/states recently and found, after setting up my recording space, that a sub 50Hz hump, largish 20kHz peak and raised noise floor appear on all recordings made through my Focusrite 2i2.
I swapped all cables, used a different computer, set up in a different room etc. but the problem persisted. I bought a power condition but things didn't change.
I bought a new, more expensive interface, SSL2, and blammo - no change.
The recording space is a rectangular, full brick built room faced with gyprock/sheetrock, timber lines ceiling and about 60 underground. It has cheap tracklights in the ceiling. Any ideas?
Last edited by rayc; 08/27/2111:31 PM.
Cheers rayc "What's so funny about peace, love & understanding?" - N.Lowe
Could you please elaborate, what do you mean by 20 kHZ peak? Most of us here haven’t been able to hear that high in over 50 years. How does this limit show itself? Your dog knows, but isn’t saying.
Assuming all your cables are the same as in the other location, are they all shielded?
Do mic and speaker cables run parallel to power lines?
Did you get an AC outlet tester to make sure the house is wired correctly (no reversed or floating grounds)?
Is all the audio equipment on one circuit (should be)? Are there other devices like a furnace, microwave, fluorescent lights or refrigerator on that circuit (shouldn’t be)?
Any radio stations or hams nearby?
Where is your router?
Any equipment suffer a beating during the move?
Tons of possibilities. Start disconnecting to try to isolate the problem.
BIAB 2026 Win Audiophile. Software: Fender Studio One 8, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Fender Quantom HD8 & Faderport 8, Royer 121, Adam Sub8 & Neumann 120 monitors.
You need to first check that there is a proper ground for the electrical system in your new house. A little two-dollar tester will be enough. Different electrical outlets frequently have a different ground reference value. Plug into one plug. Turn off your cell phone. Turn off the lights. Turn off electrical appliances one by one.
Record just the ambient noise to see what you can hear. I can hear my wife talking on the phone downstairs out in the backyard with the door closed.
I am not sure what you are recording. Guitar DI? Microphone? The lowest string on a four-string bass guitar is around 40Hz. Few people can hear above 20K Hz.
Try recording with the lights off. Those tracklights maybe part of the problem.
...Deb
Thanks Deb, That is one of a couple of things I'm interested in. they generate heat, they don't generate much light and the wiring of them s always a little suss.
Cheers rayc "What's so funny about peace, love & understanding?" - N.Lowe
Could you please elaborate, what do you mean by 20 kHZ peak? Most of us here haven’t been able to hear that high in over 50 years. How does this limit show itself? Your dog knows, but isn’t saying. Assuming all your cables are the same as in the other location, are they all shielded?Do mic and speaker cables run parallel to power lines? Did you get an AC outlet tester to make sure the house is wired correctly (no reversed or floating grounds)? Is all the audio equipment on one circuit (should be)? Are there other devices like a furnace, microwave, fluorescent lights or refrigerator on that circuit (shouldn’t be)? Any radio stations or hams nearby? Where is your router? Any equipment suffer a beating during the move? Tons of possibilities. Start disconnecting to try to isolate the problem.
Thanks Matt, 1.the peak and hum are visible on any of a number of EQs graphs within my DAW. MOST folk can't hear 20kHz but what happens up there can be heard by some and can, easily have an impact on audio recording and treatment. 2. All shielded well enough...no parallels. No outlet tester but do have the power conditioner which would rectify the supply to some degree. I will look into a tester though. On that line the ground loop switch on one of my pedals make the problem worse. Tested in other rooms down & upstairs and no change so not a single circuit thing. No appliances on the circuit. Radio station - nope semi rural location - there is a mountain though I don't have a ham radio so wouldn't really be able to tell about other ham radio users. The machine is offline and the router in the opposite corner of the house AND upstairs. The entire downstairs is brick built walls interior and exterior as well. Nope no damage, new interface has same problem. Everything has been isolated, swapped. moved and tested in various modes - including with my hand on them. Yes tons of possibilities many of which I've addressed and the reason I asked...thanks.
Cheers rayc "What's so funny about peace, love & understanding?" - N.Lowe
You need to first check that there is a proper ground for the electrical system in your new house. A little two-dollar tester will be enough. Different electrical outlets frequently have a different ground reference value. Plug into one plug. Turn off your cell phone. Turn off the lights. Turn off electrical appliances one by one.
Record just the ambient noise to see what you can hear. I can hear my wife talking on the phone downstairs out in the backyard with the door closed.
I am not sure what you are recording. Guitar DI? Microphone? The lowest string on a four-string bass guitar is around 40Hz. Few people can hear above 20K Hz.
What sort of floor do you have? Hard or carpet? The high-frequency noise is likely coming from electronics equipment such as a computer monitor.
I have to turn off my AC to record. I have to send my wife to the mall...lol
Billy
I've checked the ground spike is properly connected and well buried but haven't plugged anything into a socket/power point, (as we call them in Australia), yet.
We live in a quiet pot where a car driving down the road is remarked upon. The bush turkey, crows and magpies sing a lot, the trees sussurate a bit and any conversation in the house can be heard throughout...phones...I'd need to send my up the street not to hear her talking into one. The hump & spike come with balanced and unbalanced cables, dynamic & condensor mics, DI or mic'd guitar. Not being able to hear 20kHz (considered excellent hearing in a youngster,) of the 20Hz doesn't mean they don't have an impact on audio production though - a sub hump can often be the result of DC offset problems and cause a mass of issues. The monitor is the same as I used in NSW, all gear in the same relative position too, as is all the gear but the new interface, power conditioner and pedal power supply - all bought in an attempt to alleviate the problem. We don't have AC - yet. Thanks for the outlet tester suggestion - I'll follow it through.
Cheers rayc "What's so funny about peace, love & understanding?" - N.Lowe
You are right, a 20K Hz signal won’t be heard except maybe by grandchildren, but it will affect plug-ins attempting to analyze and process sound.
I just looked up and discovered 50 Hz is your power frequency in Australia. It’s 60 Hz in the US. That doesn’t change any of my answers.
The tester I use now is a $20 tester at Home Depot made by Klein Tools. It has a text readout in addition to the light pattern found on the $7 version that used to be all that was available. I have no idea if the one sold here for 60 Hz works in Australia but check Klein Tools. I carry a tester in every gear bag and won’t plug in any gear to an outlet before testing it first.
BIAB 2026 Win Audiophile. Software: Fender Studio One 8, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Fender Quantom HD8 & Faderport 8, Royer 121, Adam Sub8 & Neumann 120 monitors.
BIAB & RB2026 Win.(Audiophile), Windows 10 Pro & Windows 11, Cakewalk Bandlab, Izotope Prod.Bundle, Roland RD-1000, Synthogy Ivory, Session Keys Grand S & Electric R, Kontakt, Focusrite 18i20, KetronSD2, NS40M, Pioneer Active Monitors.
The 2i2 is USB powered. It doesn't plug into anything but the USB port. Are you sure the noise is coming from there?
Thanks for asking. As explained above, I'm certain it's NOT coming from the 2i2. As mentioned above the new interface presents the same issue so it's not based on the interface or preamps.
Cheers rayc "What's so funny about peace, love & understanding?" - N.Lowe
Thanks for the response folks. The power point tester is my next purchase...possibly the cheapest and easiest of the process though it could lead to some expensive modification. Thanks Noel, that's a cheap one that can be had fairly locally.
Cheers rayc "What's so funny about peace, love & understanding?" - N.Lowe
Do you have a laptop? Might be a bit overkill, but try running a laptop from battery with the Focusrite powered off it, and shut off the power to the whole house from the mains. If you're still getting the high-frequency noise coming in, then it's something environmental to the area you live in, and if it goes away then it's something powered by your house and you can hunt it down by turning on breakers one by one until you find the culprit. Once you've found the circuit it's on you can experiment with any noise filters or the like that others have mentioned.
I'd suggest using a receptacle tester on EVERY outlet in the house, not just for the noise issues but for safety. Some older equipment (old guitar amps in particular) connect the neutral line to the chassis, where if the live/neutral wiring gets swapped it'd be connecting the live 230v to the chassis!
Do you have a laptop? Might be a bit overkill, but try running a laptop from battery with the Focusrite powered off it, and shut off the power to the whole house from the mains. If you're still getting the high-frequency noise coming in, then it's something environmental to the area you live in, and if it goes away then it's something powered by your house and you can hunt it down by turning on breakers one by one until you find the culprit. Once you've found the circuit it's on you can experiment with any noise filters or the like that others have mentioned.
I'd suggest using a receptacle tester on EVERY outlet in the house, not just for the noise issues but for safety. Some older equipment (old guitar amps in particular) connect the neutral line to the chassis, where if the live/neutral wiring gets swapped it'd be connecting the live 230v to the chassis!
Thanks Simon, I've an outlet tester coming in the post and will do that part 1st then try the laptop blackout process. yes, it sounds drastic but where I lived for the previous 24 years power outages were so common that we had torches and candles at hand in all rooms as well as a camping stove and matches always at the ready. Resetting clocks is the only thing that annoys me...so many clocks need to be reset now almost any/every electronic device has a clock.
Last edited by rayc; 09/02/2109:21 PM.
Cheers rayc "What's so funny about peace, love & understanding?" - N.Lowe
Good to hear Ray! Yeah the blackout process is drastic but it's the quickest way to determine if the noise is something you can control or not - and if you can't control it, then I suppose buying cables with better shielding is in order. Hopefully the power at the new house is a bit more stable than the last one!
Interestingly, that doesn't appear to be 50Hz mains interference. The frequency is quite variable, verging on white nose perhaps.
BIAB & RB2026 Win.(Audiophile), Windows 10 Pro & Windows 11, Cakewalk Bandlab, Izotope Prod.Bundle, Roland RD-1000, Synthogy Ivory, Session Keys Grand S & Electric R, Kontakt, Focusrite 18i20, KetronSD2, NS40M, Pioneer Active Monitors.
Interestingly, that doesn't appear to be 50Hz mains interference. The frequency is quite variable, verging on white nose perhaps.
Nope, not 50Hz interference. The response isn't particularly variable...a relative straight line could be extrapolated between the the low hump and the high peak. I was told, today by a sparkie, that in Qld, a carrier freq. is used for signals to solar panel inverters. Also that the inverter may be producing interference. I'll start with a wiring check via the power outlet meter.
Cheers rayc "What's so funny about peace, love & understanding?" - N.Lowe
Does your house have any intercom system that utilizes the mains wiring to communicate data. Perhaps a neighbor has a system?
This could get tricky...
BIAB & RB2026 Win.(Audiophile), Windows 10 Pro & Windows 11, Cakewalk Bandlab, Izotope Prod.Bundle, Roland RD-1000, Synthogy Ivory, Session Keys Grand S & Electric R, Kontakt, Focusrite 18i20, KetronSD2, NS40M, Pioneer Active Monitors.
Does your house have any intercom system that utilizes the mains wiring to communicate data. Perhaps a neighbor has a system?
This could get tricky...
Quite tricky. No local intercoms and the distance between dwellings is rather larger than suburban NSW too boot. The power point tester arrived today, thanks for the link & recco, all points in the room have been tested as well as any power boards. All are AOK. I've ordered ferrite beads as the next step...oddly largely O.O.Stock in many places in Oz and LOTS of bad reviews for most online sellers (mainly masquerading as local but actually in mainland China).
Last edited by rayc; 09/08/2107:05 PM.
Cheers rayc "What's so funny about peace, love & understanding?" - N.Lowe
zplane recently interviewed Peter Gannon, the founder and creator of Band-in-a-Box, about the software's early days, what sets it apart from AI, how zplane's audio algorithms are used in Band-in-a-Box, and more!
Special thanks to the team at zplane for their continued support.
Last Chance! The Band-in-a-Box® 2026 for Mac® Special Ends Today (May 31, 2026) at 11:59pm PDT!
Time really is running out! Save up to 50% on Band-in-a-Box® 2026 for Mac® upgrades and receive a FREE Bonus PAK—only when you order by 11:59 PM PDT today!
We've added many major new features and new content in a redesigned Band-in-a-Box® 2026 for Mac®!
Version 2026 introduces a modernized GUI redesign across the program, with updated toolbars, refreshed windows, smoother workflows, and a new Dark Mode option. There’s also a new side toolbar for quicker access to commonly used windows, and the new Multi-View feature lets you arrange multiple windows as layered panels without overlap, making it easier to customize your workspace.
Another exciting new addition is the amazing new AI-Notes feature, which can transcribe polyphonic audio into MIDI. View the results in notation or play them back as MIDI, and choose whether to transcribe an entire track or transcribe specific parts like drums, bass, guitars/piano, or vocals. There's over 100 new features in Band-in-a-Box® 2026 for Mac®.
There's an amazing collection of new content too, including 202 RealTracks, new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 5, two RealDrums Stems sets, and much more!
Upgrade your Band-in-a-Box for Mac® to save up to 50% on most Band-in-a-Box® 2026 upgrade packages!
Plus, when you order your Band-in-a-Box® 2026 Mac upgrade during our special, you'll receive a Free Bonus PAK of exciting new add-ons.
If you need any help deciding which package is the best option for you, just let us know. We are here to help!
Band-in-a-Box® 2026 Mac Special Offers Extended Until May 31st!
Good news- we've extended our Band-in-a-Box® 2026 for Mac® special offers until May 31, 2026!
Band-in-a-Box® 2026 is packed with major new features, enhancements, and an incredible lineup of new content! The program now sports a sleek, modern GUI redesign across the entire interface, including updated toolbars, refreshed windows, smoother workflows, a new dark mode option, and more. The brand-new side toolbar provides quicker access to key windows, while the new Multi-View feature lets you arrange multiple windows as layered panels without overlap, creating a flexible, clutter-free workspace. We have an amazing new “AI-Notes” feature. This transcribes polyphonic audio into MIDI so you can view it in notation or play it back as MIDI. You can transcribe an entire track (all pitched instruments and drums) or focus on individual parts like drums, bass, guitars/piano, or vocals. There's an amazing collection of new content too, including 202 RealTracks, new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 5, two RealDrums Stems sets, and much more!
There are over 100 new features in Band-in-a-Box® 2026 for Mac®.
When you order purchase Band-in-a-Box® 2026 before 11:59 PM PDT on May 31st, you'll also receive a Free Bonus PAK packed with exciting new add-ons.
Check out the Band-in-a-Box® for Mac packages page to find the best package for you.
Today's the Last Day of the Band-in-a-Box 2026® for Mac Special!
Order before 11:59pm PDT today (May 15, 2026) to save up to 50% off your Band-in-a-Box® 2026 for Mac® upgrade and receive a FREE Bonus PAK loaded with great new Add-ons to use with this new version!
Band-in-a-Box® 2026 for Mac - Special Offers End at 11:59pm PDT on Friday, May 15th, 2026!
Order before 11:59pm PDT on Friday, May 15th and SAVE up to 50% on most Band-in-a-Box® version 2026 for Mac Upgrade packages... and that's not all! With your version 2026 for Mac purchase, we'll include a Bonus PAK full of great new Add-ons FREE! Upgrade to the 2026 49-PAK to receive even more NEW Add-ons including 20 additional RealTracks... that's 222 NEW RealTracks available with version Band-in-a-Box® 2026 for Mac!
Upgrade to Band-in-a-Box® 2026 for Mac® today for as little as $49! Check out the Band-in-a-Box® packages page for all available purchase options.
Learn more about the Free Bonus PAK and 49-PAK here.
If you have any questions about which package is the best option for you, just let us know. We're here to help!
202 New RealTracks Released with Band-in-a-Box 2026!
With Band-in-a-Box® 2026, we've released 202 incredible new RealTracks (in sets 468-488) in a variety of genres—featuring your most requested styles!
Jazz, Funk & World (Sets 468-475):
Our new jazz, funk & blues RealTracks include a groovin’ collection of RealTracks and RealDrums! These include more requested “soul jazz” RealTracks featuring artists Neil Swainson (bass), Charles Treadway (organ), Brent Mason (guitar), and Wes Little (drums). There are new “smooth jazz” styles (4), which include a RealTracks first: muted trumpet, as well as slick new smooth jazz brushes options for drums. Blues lovers will be thrilled—there are more “classic acoustic blues” styles, including guitar (5), bass (4), and drums (10) with blues master Colin Linden, featuring understated and tasty background acoustic soloing, plus brushes drums and acoustic bass. There are also new electric blues RealTracks, including electric blues with PG favorite Johnny Hiland (3) and soulful electric slide guitar from Colin Linden (4). If you love funk & gospel, there are great new options this year, including gospel organ (3) from Charles Treadway, as well as new funk, tango, and rock ’n’ roll drums (3) and bass (1). And for big, bold arrangements, we have uptempo soul horns (4) featuring a three-part hip horn section with options for a full mix or stems of each individual horn — plus an accompanying rhythm section (4) of drums, bass, guitar, and electric piano!
Rock & Pop (Sets 476–482):
Our new rock & pop RealTracks bring a powerful mix of requested favorites, fresh genres, and modern chart-inspired styles! We have more of our popular “Producer Layered Acoustic Guitars (15)” featuring Band-in-a-Box favorite Brent Mason. We’ve continued our much-requested disco styles (10), and added new Celtic guitar (5) with a more basic, accessible approach than our previous Drop-D or DADGAD offerings. There are also highly requested yacht rock styles (17), inspired by the smooth, polished soft-rock sound of the late ’70s and early ’80s — laid-back grooves, silky electric pianos, warm textures, elegant harmonic movement, and pristine production aesthetics. Fans of heavier styles will love our new glam metal (13), capturing the flashy, high-energy sound of ’80s arena-ready guitar rock. We also have a set of rootsy modern-folk rock (18), with a warm, organic sound combining contemporary folk textures and driving acoustic strumming. And we’ve added lots of new modern pop styles (16) — the kinds of sounds you’re hearing on the radio today, featuring exciting new drums, synths, and cutting-edge RealTracks arrangements.
Country, & Americana (Sets 483–488):
Our new country & Americana RealTracks deliver a rich collection of acoustic, electric, and roots-inspired styles! We have new country pop (9) with legendary guitarist Brent Mason. There is also a potpourri (14) of bouzouki, guitars, banjo, and more, perfect for adding texture and character to contemporary acoustic arrangements. We’ve added funky country guitar (5) with PG favorite Brent Mason, along with classic pedal steel styles (5) featuring steel great Doug Jernigan. There are more country songwriter styles (8) that provide intimate, rootsy foundations for storytelling and modern Americana writing. Finally, we have “background soloing” acoustic guitar (12) with Brent Mason — simpler, but still very tasty acoustic lines designed to sit beautifully behind vocals or act as a subtle standalone solo part.
And, if you are looking for more, the 2026 49-PAK (for $49) includes an impressive collection of 20 bonus RealTracks, featuring exciting and inspiring additions to add to your RealTracks library. You'll get new country-rhythm guitar styles from PG Music favorites Johnny Hiland and Brent Mason, along with modern-pop grooves that capture today’s radio-ready sound! There are also new indie-folk styles with guitar, bass, 6-string bass used as a high-chording instrument, acoustic guitar, and banjo. Plus, dedicated "cymbal fills" RealDrums provide an added layer that work very well with low-key folky styles with other percussion.
The 2026 49-PAK is loaded with other great new add-ons as well. Learn more about the 2026 49-PAK!
One of our representatives will be happy to help you over the phone. Our hours of operation are from
6:00AM to 6:00PM PST (GMT -8) Monday thru Friday, and 8:00AM to 4:00PM PST Saturday. We are closed Sunday. You can also send us your questions via email.
One of our representatives will be happy to help you on our Live Chat or by email. Our hours of operation are from
6:00AM to 6:00PM PST (GMT -8) Monday thru Friday; 8:00AM to 4:00PM PST (GMT -8) Saturday; Closed Sunday.
Dansk
Deutsch - Windows
Español
Français - Windows
Italiano - Windows
Nederlands
Polski
Português
Svenskt
русский
Japanese
Simplified Chinese
Traditional Chinese
Korean