|
Log in to post
|
Print Thread |
|
|
|
|
|
RealBand
|
Joined: Nov 2009
Posts: 60
Enthusiast
|
OP
Enthusiast
Joined: Nov 2009
Posts: 60 |
My RB has been crashing about every other session since I installed a M-Audio 2496 PCI card. The strange thing is, after the crash I go to reboot and get a message that biab is running. When I select the option to go to program to shut it down, I see the biab chord builder window. I did not even have biab open during the session.
Where could that be coming from?
thanks
martin
Last edited by mnich; 09/29/10 02:32 PM.
AT2020mic> ArtStudioV3VoicedValvePreAmp> M-Audio2496> AMD AthlonII 215 DualCore, 2.7GHz, 5GbDDR3Ram> Win7x64> RealBand>Ozone4> Teac A1D Amp> KRK ST6 Monitors> My old worn out ears
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Aug 2006
Posts: 8,489
Veteran
|
Veteran
Joined: Aug 2006
Posts: 8,489 |
Are you using ASIO with RB for M-Audio? If so back back down to MME i have never be able to make ASIO work well with RB. I also have a 24/96 card.
HP Win 11 12 gig ram, Mac mini Sonoma with 16 gig of ram, BiaB 2025, Realband, Reaper 7, Harrison Mixbus 9 32c , Melodyne 5 editor, Presonus Audiobox 1818VSL, Presonus control app.
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Nov 2009
Posts: 60
Enthusiast
|
|
OP
Enthusiast
Joined: Nov 2009
Posts: 60 |
I selected ASIO because it had the "enable input monitoring" option. I can't seem to monitor when recording with MME.
Last edited by mnich; 09/30/10 08:03 AM.
AT2020mic> ArtStudioV3VoicedValvePreAmp> M-Audio2496> AMD AthlonII 215 DualCore, 2.7GHz, 5GbDDR3Ram> Win7x64> RealBand>Ozone4> Teac A1D Amp> KRK ST6 Monitors> My old worn out ears
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Aug 2006
Posts: 8,489
Veteran
|
|
Veteran
Joined: Aug 2006
Posts: 8,489 |
What i do is attach a small mixer to the 24/96 and that allows me to monitor from the mixing source without any latency. Something simple and cheap like this. http://pro-audio.musiciansfriend.com/product/Behringer-XENYX-802-Mixer?sku=631263 I had one of these for a long time until i aquired a Yamaha for real cheap. I gave away the Behringer and wish i still had it today!
HP Win 11 12 gig ram, Mac mini Sonoma with 16 gig of ram, BiaB 2025, Realband, Reaper 7, Harrison Mixbus 9 32c , Melodyne 5 editor, Presonus Audiobox 1818VSL, Presonus control app.
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Nov 2009
Posts: 60
Enthusiast
|
|
OP
Enthusiast
Joined: Nov 2009
Posts: 60 |
I have a Yamaha MG10/2 that I was using. It's 48v phantom power has started humming bad. I now just go straight from an Art StudioV3 Voiced Valve PreAmp into the 2496. So I can't monitor at the ART. Would there be any issues with recording using ASIO drivers, saving, and doing everything else like generating realtracks, and mixing using MME? I haven't crashed while recording.....yet. It is usually afterwards when I hit the "rewind" button.
AT2020mic> ArtStudioV3VoicedValvePreAmp> M-Audio2496> AMD AthlonII 215 DualCore, 2.7GHz, 5GbDDR3Ram> Win7x64> RealBand>Ozone4> Teac A1D Amp> KRK ST6 Monitors> My old worn out ears
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Oct 2008
Posts: 19,807
Veteran
|
|
Veteran
Joined: Oct 2008
Posts: 19,807 |
Hi mnich,
I switch between ASIO and mme just as you describe and it's never created an issue for me. Don't be afraid to experiment. As long as you keep a copy of your original work so that you can get back to it if the experiments end in disaster, you will lose nothing.
Regards,
Noel
MY SONGS...Audiophile BIAB 2025
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 22,150
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,150 |
Plus the good old backup folder with the next most recent copy saved..
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 22,150
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,150 |
Is the enable input monitoring selection available in RB or the Delta?
You want the one on the Delta. The input monitoring in RB eats a lot of resources. You mentioned it's available with ASIO only, and that sounds like the option in RB. In the Delta applet you should be able to select input monitoring in MME (I think, as most Deltas do)
[I replied to myself, I know ...]
Last edited by rharv; 09/30/10 04:04 PM.
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Nov 2009
Posts: 60
Enthusiast
|
|
OP
Enthusiast
Joined: Nov 2009
Posts: 60 |
Yes, I was monitoring in RB. I have found that in Win7x64, my Delta control panel is missing the routing tab, and is limited to that of the earlier ones showed when I had XP. Is that where I would enable monitoring?
AT2020mic> ArtStudioV3VoicedValvePreAmp> M-Audio2496> AMD AthlonII 215 DualCore, 2.7GHz, 5GbDDR3Ram> Win7x64> RealBand>Ozone4> Teac A1D Amp> KRK ST6 Monitors> My old worn out ears
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 22,150
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,150 |
I think so, you should be able to monitor thru the card.
Look closely at monitoring options, and see if there is a driver update for W7/64 bit drivers at the M-Audio site.
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Dec 2002
Posts: 1,826
Expert
|
|
Expert
Joined: Dec 2002
Posts: 1,826 |
Hi Noel
How do you record live audio in your situation i do the same as you with real tracks and midi but a have not been able to record live audio as you can`t listen when you are using ASIO and you can`t record audio with MME
regards Dave
I always play the right notes but not always in the right order
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Oct 2008
Posts: 19,807
Veteran
|
|
Veteran
Joined: Oct 2008
Posts: 19,807 |
Hi Dave,
The only audio I record is vocals through a standard mic plugged into my sound card (i.e. not a USB mic). I downloaded and installed ASIO4ALL. This does the job well for me. I have selected Audio Set >> Enable input monitoring and that allows me to hear myself through the mic while the recording is in progress. ASIO4ALL gives me practically zero latency when recording vocals. (By comparison, when I used MME, there was a slight latency; when I tried my soundcard's (Audigy 2) ASIO drivers, the latency was very noticeable.)
All the best,
Noel
MY SONGS...Audiophile BIAB 2025
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 22,150
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,150 |
According to M-Audio all deltas allow realtime monitoring from inside the card, with control over the input signal and the rest of the mix- http://www.m-audio.com/?do=support.faq&ID=8afcce81d0497cd75e842fe26a5b6f81&lang=en"With "mixer" selected as the output source for outputs 1/2, you can now use the volume sliders on the Mixer page to control the levels of the various hardware inputs and software outputs going to your speakers. Turning up the levels for the inputs allows you to directly monitor your input source while recording, with virtually no latency." Does this not work on 2496? I'm curious.
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Aug 2006
Posts: 8,489
Veteran
|
|
Veteran
Joined: Aug 2006
Posts: 8,489 |
Works here but i have not used it recently as I use the external mixer for all that stuff.
HP Win 11 12 gig ram, Mac mini Sonoma with 16 gig of ram, BiaB 2025, Realband, Reaper 7, Harrison Mixbus 9 32c , Melodyne 5 editor, Presonus Audiobox 1818VSL, Presonus control app.
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Nov 2009
Posts: 60
Enthusiast
|
|
OP
Enthusiast
Joined: Nov 2009
Posts: 60 |
I finally got my 2496 to monitor with MME, once I found the output to mixer option. And I haven't crashed RB since switching from ASIO to MME.
thanks everyone!
AT2020mic> ArtStudioV3VoicedValvePreAmp> M-Audio2496> AMD AthlonII 215 DualCore, 2.7GHz, 5GbDDR3Ram> Win7x64> RealBand>Ozone4> Teac A1D Amp> KRK ST6 Monitors> My old worn out ears
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 22,150
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,150 |
Yeah, the new drivers look different, but do perform the same functions .. just in a different place sometimes.
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
Ask sales and support questions about Band-in-a-Box using natural language.
ChatPG's knowledge base includes the full Band-in-a-Box User Manual and sales information from the website.
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box 2025 Italian Version is Here!
Cari amici
È stata aggerate la versione in Italiano del programma più amato dagli appassionati di musica, il nostro Band-in-a-Box.
Questo è il link alla nuova versione 2025.
Di seguito i link per scaricare il pacchetti di lingua italiana aggiornati per Band-in-a-Box e RealBand, anche per chi avesse già comprato la nuova versione in inglese.
Band-in-a-Box 2025 - Italiano
RealBand 2025 - Italiano
Band-in-a-Box 2025 French Version is Here!
Bonjour à tous,
Band-in-a-Box® 2025 pour Windows est disponible en Français.
Le téléchargement se fait à partir du site PG Music
Pour ceux qui auraient déjà acheté la version 2025 de Band-in-a-Box (et qui donc ont une version anglaise), il est possible de "franciser" cette version avec les patchs suivants:
BIAB 2025 - francisation
RealBand 2025 - francisation
Voilà, enjoy!
Band-in-a-Box 2025 German Version is Here!
Update Your Band-in-a-Box® 2025 to Build 1128 for Windows Today!
Already using Band-in-a-Box 2025 for Windows®? Download Build 1128 now from our Support Page to enjoy the latest enhancements and improvements from our team.
Stay up to date—get the latest update now!
Update to RealBand® 2025 Build 5 Windows Today!
Already using RealBand® 2025 for Windows®? Download Build 5 now from our Support Page to ensure you have the latest enhancements and improvements from our team.
Get the latest update today!
PowerTracks Pro Audio 2025 for Windows is Here!
PowerTracks Pro Audio 2025 is here! This new version introduces many features, including VST3 support, the ability to load or import a .FLAC file, a reset option for track height in the Tracks window, a taller Timeline on the Notation window toolbar, new freeze buttons in the Tracks window, three toolbar modes (two rows, single row, and none), the improved Select Patch dialog with text-based search and numeric patch display, a new button in the DirectX/VST window to copy an effects group, and more!
First-time packages start at only $49. Already a PowerTracks Pro Audio user? Upgrade for as little as $29!
www.pgmusic.com/powertracks.htm
Video: Summary of the New Band-in-a-Box® App for iOS®
Join Tobin as he takes you on a tour of the new Band-in-a-Box® app for iOS®! Designed for musicians, singer-songwriters, and educators, this powerful tool lets you create, play, and transfer songs effortlessly on your iPhone® or iPad®—anytime, anywhere.
Band-in-a-Box® for iOS® :Summary video.
Check out the forum post for more information.
|
|
|
|
|
|
|
|
|
|
|
|
Forums58
Topics84,136
Posts775,664
Members39,584
| |
Most Online25,754
Jan 24th, 2025
|
|
|
|
|
|
|
|
|
Dansk
Deutsch - Windows
Español
Français - Windows
Italiano - Windows
Nederlands
Polski
Português
Svenskt
русский
Japanese
Simplified Chinese
Traditional Chinese
Korean