|
Log in to post
|
Print Thread |
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Aug 2013
Posts: 34
Enthusiast
|
OP
Enthusiast
Joined: Aug 2013
Posts: 34 |
I am new to BIAB and want to use it (or RealBand) to drag and drop RealTracks audio files to my DAW of choice, Sonar X2 Producer. I can get the tracks to drag and drop just fine but for whatever reason I can't pan the tracks after dropping them into my DAW. I experience this issue whether I'm working with a stereo or mono track and have taken the extra step to convert stereo tracks to mono in Sonar, etc.
Reading through the forums here, I read about clicking on Combo and setting the song to "Set Mix to Flat, Dry, and Center". This didn't help either.
No matter what I attempt, the track is silent when panned 100% left and gets louder as I bring it up toward center. As I continue to pan toward full right, nothing changes at all.
I'd appreciate any insight into this. I love the product but have a few hiccups such as this I'll post questions about. Thanks in advance for your help.
Also what work flow do you prefer for dragging and dropping tracks into another DAW? I'm using BIAB to arrange things and RealBand to add additional tracks. Then I'm dragging into Sonar. Is this the preferred method or do you simply drag and drop from BIAB into another DAW other than RealBand?
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Feb 2007
Posts: 1,815
Expert
|
|
Expert
Joined: Feb 2007
Posts: 1,815 |
In BIAB I always center pan all tracks and increase the volume as needed and then render with a mono or stereo file for each track. I then import them into sonar one at a time (I could do drag and drop, but I normally don't). That way when I pan in Sonar, 25% right is actually 25% right!
There are other ways to do, but that is my method.
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
No matter what I attempt, the track is silent when panned 100% left and gets louder as I bring it up toward center. As I continue to pan toward full right, nothing changes at all.
XXYou don't say which DAW you are using,XX --Whoops, my bad, you do say Sonar sorry -- but the above seems to indicate that you are importing with a DAW setting somewhere that puts each track on the R channel only. Look for a setting n the DAW that allows for import onto both channels. NOTE: This also describes what can happen if the L channel output is inoperative, either due to software setting or something amiss in hardware at output, bad connection, bad cable, improper soundcard output setting, etc. --Mac
Last edited by Mac; 10/07/13 03:04 PM. Reason: Mac's poor reading comprehension...
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Jul 2000
Posts: 27,449
Veteran
|
Veteran
Joined: Jul 2000
Posts: 27,449 |
BigWhirl2012, a few thoughts, not necessarily in order:
Like you, I use SONAR, but I can drag the Combo with success.
Normally I do set the BIAB tracks to flat, dry, and center first but it will work without doing so.
I have never seen your problem, where SONAR requires the track to be panned in the center or all the way to the right just to be heard. Thus, I would suspect something in SONAR or your audio setup to be the fix here, rather than BIAB.
Are you sure you have sound in both speakers using other sound sources? Bad cable, that sort of thing...
Are you sure your mixer is set correctly with sound to the left channel? Are there any plugins on the main bus that could be set to pan only right?
By the way, I like SONAR X3 so far.
As to the Realband versus other DAWs, others here can answer better than I, because I do not use Realband. The reason for that is that I learned Cakewalk Pro Audio, then SONAR, long before PG Music released RealBand. However, I do know there are some important advantages to be found by using Realband in between BIAB and your DAW, such as the ability to exceed 255 measures and the ability to regenerate parts of a track. I'm sure there are others.
EDIT: I see Mac also suspects something amiss in the setup.
Last edited by Matt Finley; 10/07/13 02:00 PM.
BIAB 2025 Win Audiophile. Software: Studio One 7 Pro, Swam horns, Acoustica-7, Notion 6, Song Master Pro, Win 11 Home. Hardware: Intel i9, 32 Gb; Presonus 192 & Faderport 8, Royer 121, Slate VSX, Adam Sub8 & Neumann 120 monitors.
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Aug 2013
Posts: 34
Enthusiast
|
|
OP
Enthusiast
Joined: Aug 2013
Posts: 34 |
I just tried panning in RB and got the same results. I have an acoustic bass track that shows in the tracks pane to be a mono track. But when I hit play and switch to the mixer screen, it shows the track to as a stereo track with a distinct left and right channel on it and a peak indicator assigned to each. When I attempt to pan hard left- nothing but I can still see the left channel peak indicator bouncing up and down . As I start inching the pan control toward center, I start hearing something. At center panning, both the left and ran indicator move. The farther I move to the right, the volume doesn't change but the left peak indicator decreases and finally stops working altogether at hard right.
And Mac, I'm using Sonar X2 Producer.
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
Does the same thing with a completely different program.
The VU meters in RB are trustworthy, that means there is a signal there.
The signal is not reaching the speaker for some reason.
Check connections, check speaker connections, check amplifier connections, check amplifier, check speaker.
Your L channel likely isn't working anywhere on anything from the descriptions given.
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Aug 2013
Posts: 34
Enthusiast
|
|
OP
Enthusiast
Joined: Aug 2013
Posts: 34 |
I finally fixed it! The problem was neither a BB, RB, or Sonar issue. The issue was with Focusrite's infamous Scarlett Mix Control software (which I hate with a fiery passion)!
Thanks to everyone here who chimed in with encouragement and technical advice. I really appreciate it!
David
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
NOTE: This also describes what can happen if the L channel output is inoperative, either due to software setting or something amiss in hardware at output, bad connection, bad cable, improper soundcard output setting, etc.
--Mac
Glad you got it sorted, Have Fun! --Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Apr 2009
Posts: 10,726
Veteran
|
|
Veteran
Joined: Apr 2009
Posts: 10,726 |
Hummm...
I use Sonar X1. I render the tracks from BB in Real Band as audio and then I export them one at a time from RB to a folder on my desktop. It's actually a subfolder of a folder on the desk top but you catch the idea....
They are not given any special settings in real band.... I simply choose the tracks and let RB create them. TO my knowledge, they are not panned.
If I recall correctly however, Band in a Box does use default pan settings for it's tracks. I don't change that and simply open the BB project with RB and let it render as it will. I have not really noticed if the BB tracks are panned in RB.... but they don't seem to be, and quite often I do NOT use the first tracks created in RB..... I render all new ones for what I want and need.
Once they are in the folder, I simply close BB & RB and open X1 with a new project. I add audio tracks and proceed to use the IMPORT AUDIO one track at a time to X!'s tracks. They all come in centered.
I can then pan them from center to 100% hard L or R as the need dictates.... or anywhere in between.
I also tend to NOT work in stereo with the tracks unless that track comes in as stereo. Mono up the center is preferred.
If the track is stereo, be sure it has 2 unique waves in that track and they should both be approximately equal in size and strength. A stereo track should pan just as easily as a mono track.
Last edited by Guitarhacker; 10/08/13 04:33 AM.
You can find my music at: www.herbhartley.comAdd nothing that adds nothing to the music. You can make excuses or you can make progress but not both. The magic you are looking for is in the work you are avoiding.
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
The type of Panning needed for a Stereo Track is called, "Equal Energy Panning".
Some early DAW programs (I seem to recall the old Cakewalk pro 9 being one) the setting was manual and set by the user. Many users did not know about the thing and likely hurt themselves when attempting to mix.
In Realband (and PT as well), the function is automatic.
If you have a Stereo Track, which is easy to tell because you will see two audio graphic waveform tracks one above the other on one track, RB/PT automatically knows to use the Equal Energy Panning algorithm.
So you can just use the PAN control on any track, stereo or mono, and achieve the proper result.
While most times for most instruments we can use a Mono track, there are indeed times when use of a Stereo track for the one instrument has its advantages.
For example, a good Stereo Grand Piano, whether from MIDI samples or from the real, it is the mic'ing that makes the huge difference in sound quality - and if you listen closely you will hear that the lower side of the piano's notes favor the mic that is over the bass bout of strings, while the treble or high side is favoring the other channel, where the mic is typically placed not over the strings but over the hammers or bridge of the piano. Panning that sound using Equal Energy Panning allows us to still be able to place that stereo grand piano somewhere in the L to R soundstage, but still preserving that desired full sound.
Another good example would be the mic'd Acoustic Guitar, where it is often the case that we can get a great sound by mic'ing the area near the soundhole in one channel while simultaneously mic'ing the area above the high end of the fretboard in the other channel, capturing both the low end to mids of the box while at the same time capturing the strings and the fingering sounds. Again, this type of stereo track responds very well to the Panning and can be placed anywhere in the soundstage's horizontal aspect without losing that full stereo sound of the instrument.
An important aspect of mixing stereo should be mentioned here.
I always-always take a listen to my work in Mono before releasing a mix.
To do that, I use the switch on my monitors' preamplifier to sum both channels to Mono easily, but this can also be done in software in a lot of DAWs, handy for those that perhaps use powered monitors without a Mono switch available.
Listen to your Stereo Mix in mono at low "conversational" levels, for any phase cancellation problems. If a certain instrument sounds "thin" or chorused in Mono mode, that indicates that there is a Phasing problem that should be solved in the mix.
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
Ask sales and support questions about Band-in-a-Box using natural language.
ChatPG's knowledge base includes the full Band-in-a-Box User Manual and sales information from the website.
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box 2026 for Windows Special Offers End Tomorrow (January 15th, 2026) at 11:59 PM PST!
Time really is running out! Save up to 50% on Band-in-a-Box® 2026 for Windows® upgrades and receive a FREE Bonus PAK—only when you order by 11:59 PM PST on Thursday, January 15, 2026!
We've added many major new features and new content in a redesigned Band-in-a-Box® 2026 for Windows®!
Version 2026 introduces a modernized GUI redesign across the program, with updated toolbars, refreshed windows, smoother workflows, and a new Dark Mode option. There’s also a new side toolbar for quicker access to commonly used windows, and the new Multi-View feature lets you arrange multiple windows as layered panels without overlap, making it easier to customize your workspace.
Another exciting new addition is the new AI-Notes feature, which can transcribe polyphonic audio into MIDI. You can view the results in notation or play them back as MIDI, and choose whether to process an entire track or focus on specific parts like drums, bass, guitars/piano, or vocals. There's over 100 new features in Band-in-a-Box® 2026 for Windows®.
There's an amazing collection of new content too, including 202 RealTracks, new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 5, two RealDrums Stems sets, XPro Styles PAK 10, Xtra Styles PAK 21, and much more!
Upgrade your Band-in-a-Box for Windows to save up to 50% on most Band-in-a-Box® 2026 upgrade packages!
Plus, when you order your Band-in-a-Box® 2026 upgrade during our special, you'll receive a Free Bonus PAK of exciting new add-ons.
If you need any help deciding which package is the best option for you, just let us know. We are here to help!
Band-in-a-Box® 2026 for Windows® Special Offers Extended Until January 15, 2026!
Good news! You still have time to upgrade to the latest version of Band-in-a-Box® for Windows® and save. Our Band-in-a-Box® 2026 for Windows® special now runs through January 15, 2025!
We've packed Band-in-a-Box® 2026 with major new features, enhancements, and an incredible lineup of new content! The program now sports a sleek, modern GUI redesign across the entire interface, including updated toolbars, refreshed windows, smoother workflows, a new dark mode option, and more. The brand-new side toolbar provides quicker access to key windows, while the new Multi-View feature lets you arrange multiple windows as layered panels without overlap, creating a flexible, clutter-free workspace. We have an amazing new “AI-Notes” feature. This transcribes polyphonic audio into MIDI so you can view it in notation or play it back as MIDI. You can process an entire track (all pitched instruments and drums) or focus on individual parts like drums, bass, guitars/piano, or vocals. There's an amazing collection of new content too, including 202 RealTracks, new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 5, two RealDrums Stems sets, XPro Styles PAK 10, Xtra Styles PAK 21, and much more!
There are over 100 new features in Band-in-a-Box® 2026 for Windows®.
When you order purchase Band-in-a-Box® 2026 before 11:59 PM PST on January 15th, you'll also receive a Free Bonus PAK packed with exciting new add-ons.
Upgrade to Band-in-a-Box® 2026 for Windows® today! Check out the Band-in-a-Box® packages page for all the purchase options available.
Happy New Year!
Thank you for being part of the Band-in-a-Box® community.
Wishing you and yours a very happy 2026—Happy New Year from all of us at PG Music!
Season's Greetings!
Wishing everyone a happy, healthy holiday season—thanks for being part of our community!
The office will be closed for Christmas Day, but we will be back on Boxing Day (Dec 26th) at 6:00am PST.
Team PG
Band-in-a-Box 2026 Video: The Newly Designed Piano Roll Window
In this video, we explore the updated Piano Roll, complete with a modernized look and exciting new features. You’ll see new filtering options that make it easy to focus on specific note groups, smoother and more intuitive note entry and editing, and enhanced options for zooming, looping, and more.
Watch the video.
You can see all the 2026 videos on our forum!
Band-in-a-Box 2026 Video: AI Stems & Notes - split polyphonic audio into instruments and transcribe
This video demonstrates how to use the new AI-Notes feature together with the AI-Stems splitter, allowing you to select an audio file and have it separated into individual stems while transcribing each one to its own MIDI track. AI-Notes converts polyphonic audio—either full mixes or individual instruments—into MIDI that you can view in notation or play back instantly.
Watch the video.
You can see all the 2026 videos on our forum!
Bonus PAK and 49-PAK for Band-in-a-Box® 2026 for Windows®
With your version 2026 for Windows Pro, MegaPAK, UltraPAK, UltraPAK+, Audiophile Edition or PlusPAK purchase, we'll include a Bonus PAK full of great new Add-ons for FREE! Or upgrade to the 2026 49-PAK for only $49 to receive even more NEW Add-ons including 20 additional RealTracks!
These PAKs are loaded with additional add-ons to supercharge your Band-in-a-Box®!
This Free Bonus PAK includes:
- The 2026 RealCombos Booster PAK:
-For Pro customers, this includes 27 new RealTracks and 23 new RealStyles.
-For MegaPAK customers, this includes 25 new RealTracks and 23 new RealStyles.
-For UltraPAK customers, this includes 12 new RealStyles.
- MIDI Styles Set 92: Look Ma! More MIDI 15: Latin Jazz
- MIDI SuperTracks Set 46: Piano & Organ
- Instrumental Studies Set 24: Groovin' Blues Soloing
- Artist Performance Set 19: Songs with Vocals 9
- Playable RealTracks Set 5
- RealDrums Stems Set 9: Cool Brushes
- SynthMaster Sounds Set 1 (with audio demos)
- Android Band-in-a-Box® App (included)
Looking for more great add-ons, then upgrade to the 2026 49-PAK for just $49 and you'll get:
- 20 Bonus Unreleased RealTracks and RealDrums with 20 RealStyle.
- FLAC Files (lossless audio files) for the 20 Bonus Unreleased RealTracks and RealDrums
- MIDI Styles Set 93: Look Ma! More MIDI 16: SynthMaster
- MIDI SuperTracks Set 47: More SynthMaster
- Instrumental Studies 25 - Soul Jazz Guitar Soloing
- Artist Performance Set 20: Songs with Vocals 10
- RealDrums Stems Set 10: Groovin' Sticks
- SynthMaster Sounds & Styles Set 2 (sounds & styles with audio demos)
Learn more about the Bonus PAKs for Band-in-a-Box® 2026 for Windows®!
|
|
|
|
|
|
|
|
|
|
|
|
Forums57
Topics85,738
Posts795,588
Members39,945
| |
Most Online25,754
Jan 24th, 2025
|
|
|
|
|
|
|
|
|
Dansk
Deutsch - Windows
Español
Français - Windows
Italiano - Windows
Nederlands
Polski
Português
Svenskt
русский
Japanese
Simplified Chinese
Traditional Chinese
Korean