|
Log in to post
|
Print Thread |
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Jun 2005
Posts: 7,697
Veteran
|
Veteran
Joined: Jun 2005
Posts: 7,697 |
Yes! That Mackie is a great audio interface. Look at page 10 and 11 of your owners manual. It tells you the Mackie receives the two channel main mix from your computer via the USB cable. That means you do NOT run audio from the back of your PC, the audio is going out from the Mackie. Here's where it's a little tricky for you if your not used to this. The Mackie uses XLR connectors for the main audio output. That means you have to get XLR cables to run to either your studio power amp or your powered monitor speakers. Note what it says on page 11 about adjusting the USB audio output coming from your computer. I'll bet that's where your problem lies with the weak sound you're describing since you're saying you have adjusted your wav outputs to the max already.
The one thing missing on the Mackie is midi but you may not need that. All newer keyboards/sound modules use USB for midi and the audio. My Roland Sonic cell for example. It's hooked up via USB so it plays any midi tracks and the audio outputs goes to my studio monitoring system which is controlled by my Behringer mixer, in your case any audio outputs from any other equipment goes into your Mackie. If you have some older equipment that does not have USB and you want to use it for midi sounds then you would need a separate USB midi adapter to go along with the Mackie but the audio outputs still goes to the Mackie.
Bob
Biab/RB latest build, Win 11 Pro, Ryzen 5 5600 G, 512 Gig SSD, 16 Gigs Ram, Steinberg UR22 MkII, Roland Sonic Cell, Kurzweil PC3, Hammond SK1, Korg PA3XPro, Garritan JABB, Hypercanvas, Sampletank 3, more.
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Jun 2005
Posts: 7,697
Veteran
|
|
Veteran
Joined: Jun 2005
Posts: 7,697 |
Quote:
Again with USB connection i only get control over the Graphic EQ Becuase with USB the computer is not feeding through one of the single pre amps 7/8 input .
Regards,
Greg
Greg, you must have written this at the same time I was posting my last reply.
This is the way you want it to work, you want to use the USB, not the 1/8" audio mini plug. Everything concerning the sound quality is done inside whatever software you're using, in this case Biab. The whole point of using a DAW is for you to do your final mixing there before it's sent out to your studio monitoring system. That includes any EQ. You keep your mixer EQ set flat, otherwise you don't know what your actual mix sounds like because that's external to the mix. If you keep the Mackie flat and your mix sounds like crap, then you fix it inside the software. Mackie included that EQ section for live work where as they described, you may want to mix the output from a laptop with vocals or instruments on stage but for studio mixing that's the last thing you want to do is to color the USB output from your PC.
Are using good XLR cables for the main outs?
Bob
Biab/RB latest build, Win 11 Pro, Ryzen 5 5600 G, 512 Gig SSD, 16 Gigs Ram, Steinberg UR22 MkII, Roland Sonic Cell, Kurzweil PC3, Hammond SK1, Korg PA3XPro, Garritan JABB, Hypercanvas, Sampletank 3, more.
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Apr 2011
Posts: 71
Enthusiast
|
|
OP
Enthusiast
Joined: Apr 2011
Posts: 71 |
Hi Bob and thanks for that last reply. I am using good cables for my sound system .I bought them from sweetwater. I think the 1/8 connection sounded better then the USB becuase those on line BIAB demos are set at flat response and they are compressed files .So when i run it through the 1/8 plug to 1/4 im able to get more gain through the pre amp channel 7/8 becuase i have the low .mid ,and high adjustments And im able to doctor up those flat response demos . I understand now that i need to go all the fixing in BIAB first then out from USB connection It all makes sence now . Do i need to buy and audio interface or is my mixer with the USB connection the audio interface ? Thanks for your support
Mackie PRO FX8
Regards, Greg
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Apr 2011
Posts: 71
Enthusiast
|
|
OP
Enthusiast
Joined: Apr 2011
Posts: 71 |
Bob Disregard my question about my mixer being an audio interface i just read your answer to that . lol
Regards,
Greg
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Apr 2011
Posts: 71
Enthusiast
|
|
OP
Enthusiast
Joined: Apr 2011
Posts: 71 |
Hi Bob again,
I went a head and hooked the USB up to my mixer .Boy what a sound ! I went into my computer and looked at my main volume level and it was only up 1/4 of the way .I got plenty of juice now. lol . I got so much power it's unreal. The sound is cleaner and smoother and that's is even with a demo .I can't imagine what these real styles will sound like once i take them into the mixing area of the program. I have my mic pluged into channel one on my mixer and for some reason i do not get the feed back coming through my mic anymore like i use to .Is there a reason for that ? Another thing that helped i took the longest wall in the room and stretched my speakers out more. Why does USB sound better then anolog ? Anyways i can breath a little easer now i think im heading in the right direction. The more im listening to these real styles now I'm starting to think BIAB sound's more life like compared to the arranger keyboards out there. Man when i hear that sax it's out of this world . lol Here i had an audio interface on my mixer and was not even using it. lol As faras my main out puts to my amp im using the main outs on the front panel of my mixer L/R they are 1/4 jacks going into 3 prong plug on the other end which goes into my power amp but it also gives me a choice i could also select the 1/4 inch jacks in .Does it matter if i have 1/4 jack coming out of my main mixer and then going in with the 3 prong plug on the other end ? I could have just used 1/4 to 1/4 from mixer to amp but as if now it's 1/4 to the 3 prong plug.
Regards,
Greg
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Apr 2011
Posts: 71
Enthusiast
|
|
OP
Enthusiast
Joined: Apr 2011
Posts: 71 |
Hi Bob i was looking at my mixer again for hooking the mixer up to the power amp .I see there are XLR OUT PUTS on the back of my Mackie .I did not hook it up from the back but rather i hooked the main out from the top Bal/ unbal main out .So one end is 1/4 inch and the other end going to my power amp is XLR. Should i hook my mains from the back of the mixer and to my amp with XLR Only ? I wounder if that would make a difference in sound ? My power amp gives me an option either i can connect with 1/4 or XLR Inputs same does for the mixer. It apears the manule is saying the out mains are in the back of the mixer but do not talk about the main outs on top as far as a i can see .Which way would you hook it up ? Mackie pro FX8
Regards,
Greg
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Jun 2005
Posts: 7,697
Veteran
|
|
Veteran
Joined: Jun 2005
Posts: 7,697 |
Quote:
I went into my computer and looked at my main volume level and it was only up 1/4 of the way .I got plenty of juice now.
Quote:
As faras my main out puts to my amp im using the main outs on the front panel of my mixer L/R they are 1/4 Does it matter if i have 1/4 jack coming out of my main mixer and then going in with the 3 prong plug on the other end ? I could have just used 1/4 to 1/4 from mixer to amp but as if now it's 1/4 to the 3 prong plug.
A quick comment here, Greg. Mac told you several days ago to make sure the main volume level was up full in your computer. That alone would have made a big difference even with the 1/8" mini plug going to your PA. When you have questions you need to read the answers carefully. Still, you're much better off using your Mackie anyway and now you've got it set up properly so that's great.
As to your second question no, it doesn't matter as far as sound quality is concerned, the 1/4" jacks on the front panel say "Main Out" so it should be the same as using the XLR Main Out on the back. It's cleaner and less messy looking to have the mains coming out the back and if you want to get technical about it balanced XLR's are what the pro's use over 1/4" jacks because of less chance of interference and noise. Mackie makes pro level mixers, that's why the mains on the back are XLR's and it's the same on my Behringer mixer too. If you're not hearing any noise then you're fine with the 1/4".
You're on your way now Greg and as Peter says, have some fun!
Bob
Biab/RB latest build, Win 11 Pro, Ryzen 5 5600 G, 512 Gig SSD, 16 Gigs Ram, Steinberg UR22 MkII, Roland Sonic Cell, Kurzweil PC3, Hammond SK1, Korg PA3XPro, Garritan JABB, Hypercanvas, Sampletank 3, more.
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Apr 2011
Posts: 71
Enthusiast
|
|
OP
Enthusiast
Joined: Apr 2011
Posts: 71 |
Thanks Bob for all your help .About the volume i will double check to make sure my volume is all the way up on my computer .Even when it was lower i still had plenty of volume so i guss that is showing me that the usb connection is pumping a better signal from my computer compared to the 1/8 jack hook up . So it's volume all the way up on the computer and lower the volume on the mixer i got it. I talked with Mackie tec support today .He said both out put connections are ok either 1/4 or XLR connection but he said like you said the XLR gives a less chance of interference with Noise .As of now i have a 1/4 inch jacks going from my mixer to the input of my power amp by way of XLR connection. I orderd a pair of Pro co XLR cables today from sweetwater .I like the idea of the jacks being the same set up on both sides male to female connection XLR and like you said it looks less messy becuase the jacks are on the back. Again thank you and the forum for leading me in the right direction .
Regards,
Greg
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: May 2000
Posts: 22,545
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,545 |
Quote:
Why does USB sound better then anolog ?
For one thing the conversion from a digital signal to an audio signal is now being done by the Mackie, which was designed for the job. Which do you think was built with better digital-audio convertors; Mackie mixer or laptop? I betting the Mackie <grin>
Use the best convertors you have on hand for the best sound. That goes both ways. Your recorded tracks (like vocals) will probably sound better letting the Mackie do the conversion compared to the onboard laptop device.
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Apr 2011
Posts: 71
Enthusiast
|
|
OP
Enthusiast
Joined: Apr 2011
Posts: 71 |
http://www.box.net/shared/bhmsa71ae7d856slbrqx http://www.box.net/shared/9d3pho8foc Bob here is a song file that a fellow sent me On the interent a while back which is from BIAB and im singing with it. I added my voice in Audacity and then recorded. The second link was an arragment that i created when i use to own the Yamaha psrs 900 arranger keyboard .The guitar part i did with the Pitch bend wheel while playing the keys. Although it sounded half decent i gave up trying to learn how to play the keys ,it destracted me from my singing skills so that is why i will be going with BIAB in the future but any way i thought i would share these two arrangment with you .Again thanks for taken the time in helping me get started with recording . Take care my friend . Regards, Greg
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Mar 2011
Posts: 95
Enthusiast
|
|
Enthusiast
Joined: Mar 2011
Posts: 95 |
Great vocal on San Francisco Greg.
|
|
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box for Windows
|
Joined: Apr 2011
Posts: 71
Enthusiast
|
|
OP
Enthusiast
Joined: Apr 2011
Posts: 71 |
Thank you Bert glad you enjoyed it .
Regards,
Greg
|
|
|
|
|
|
|
|
|
|
|
|
Ask sales and support questions about Band-in-a-Box using natural language.
ChatPG's knowledge base includes the full Band-in-a-Box User Manual and sales information from the website.
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box® 2025 for Mac® users: Build 904 now available!
If you're already using Band-in-a-Box® 2025 for Mac®, make sure to grab the latest update! Build 904 is now available for download and includes the newest additions and enhancements from our team.
Band-in-a-Box® 2026 for Windows® users: Build 1237 is now available!
Already a Band-in-a-Box 2026 for Windows user? Stay up to date and download the build 1237 to get all the latest additions and enhancements.
PowerTracks Pro 2026 for Windows is Here!
PowerTracks 2026 is here—bringing powerful new enhancements designed to make your production workflow faster, smoother, and more intuitive than ever.
The enhanced Mixer now shows Track Type and Instrument icons for instant track recognition, while a new grid option simplifies editing views. Non-floating windows adopt a modern title bar style, replacing the legacy blue bar.
The Master Volume is now applied at the end of the audio chain for consistent levels and full-signal master effects.
Tablature now includes a “Save bends when saving XML” option for improved compatibility with PG Music tools. Plus, you can instantly match all track heights with a simple Ctrl-release after resizing, and Add2 chords from MGU/SGU files are now fully supported... and more!
Get started today—first-time packages start at just $49.
Already using PowerTracks Pro Audio? Upgrade for as little as $29 and enjoy the latest improvements!
Order now!
Band-in-a-Box 2026 for Windows Special Offers End Tomorrow (January 15th, 2026) at 11:59 PM PST!
Time really is running out! Save up to 50% on Band-in-a-Box® 2026 for Windows® upgrades and receive a FREE Bonus PAK—only when you order by 11:59 PM PST on Thursday, January 15, 2026!
We've added many major new features and new content in a redesigned Band-in-a-Box® 2026 for Windows®!
Version 2026 introduces a modernized GUI redesign across the program, with updated toolbars, refreshed windows, smoother workflows, and a new Dark Mode option. There’s also a new side toolbar for quicker access to commonly used windows, and the new Multi-View feature lets you arrange multiple windows as layered panels without overlap, making it easier to customize your workspace.
Another exciting new addition is the new AI-Notes feature, which can transcribe polyphonic audio into MIDI. You can view the results in notation or play them back as MIDI, and choose whether to process an entire track or focus on specific parts like drums, bass, guitars/piano, or vocals. There's over 100 new features in Band-in-a-Box® 2026 for Windows®.
There's an amazing collection of new content too, including 202 RealTracks, new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 5, two RealDrums Stems sets, XPro Styles PAK 10, Xtra Styles PAK 21, and much more!
Upgrade your Band-in-a-Box for Windows to save up to 50% on most Band-in-a-Box® 2026 upgrade packages!
Plus, when you order your Band-in-a-Box® 2026 upgrade during our special, you'll receive a Free Bonus PAK of exciting new add-ons.
If you need any help deciding which package is the best option for you, just let us know. We are here to help!
Band-in-a-Box® 2026 for Windows® Special Offers Extended Until January 15, 2026!
Good news! You still have time to upgrade to the latest version of Band-in-a-Box® for Windows® and save. Our Band-in-a-Box® 2026 for Windows® special now runs through January 15, 2025!
We've packed Band-in-a-Box® 2026 with major new features, enhancements, and an incredible lineup of new content! The program now sports a sleek, modern GUI redesign across the entire interface, including updated toolbars, refreshed windows, smoother workflows, a new dark mode option, and more. The brand-new side toolbar provides quicker access to key windows, while the new Multi-View feature lets you arrange multiple windows as layered panels without overlap, creating a flexible, clutter-free workspace. We have an amazing new “AI-Notes” feature. This transcribes polyphonic audio into MIDI so you can view it in notation or play it back as MIDI. You can process an entire track (all pitched instruments and drums) or focus on individual parts like drums, bass, guitars/piano, or vocals. There's an amazing collection of new content too, including 202 RealTracks, new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 5, two RealDrums Stems sets, XPro Styles PAK 10, Xtra Styles PAK 21, and much more!
There are over 100 new features in Band-in-a-Box® 2026 for Windows®.
When you order purchase Band-in-a-Box® 2026 before 11:59 PM PST on January 15th, you'll also receive a Free Bonus PAK packed with exciting new add-ons.
Upgrade to Band-in-a-Box® 2026 for Windows® today! Check out the Band-in-a-Box® packages page for all the purchase options available.
Happy New Year!
Thank you for being part of the Band-in-a-Box® community.
Wishing you and yours a very happy 2026—Happy New Year from all of us at PG Music!
Season's Greetings!
Wishing everyone a happy, healthy holiday season—thanks for being part of our community!
The office will be closed for Christmas Day, but we will be back on Boxing Day (Dec 26th) at 6:00am PST.
Team PG
|
|
|
|
|
|
|
|
|
|
|
|
Forums57
Topics86,063
Posts799,682
Members40,026
| |
Most Online44,367
Mar 4th, 2026
|
|
|
|
|
|
|
|
|
|
|
|
There are no members with birthdays on this day. |
|
|
|
|
|
|
|
|
Dansk
Deutsch - Windows
Español
Français - Windows
Italiano - Windows
Nederlands
Polski
Português
Svenskt
русский
Japanese
Simplified Chinese
Traditional Chinese
Korean