|
Log in to post
|
Print Thread |
|
|
|
|
|
Off-Topic
|
Joined: Sep 2007
Posts: 3,926
Veteran
|
Veteran
Joined: Sep 2007
Posts: 3,926 |
What we have here is failure to cmyoonicate. I know what I'm saying is true but can't explain it any better at the moment (working). I'll come back to it, or maybe someone can clarify it before then.
"My primary musical instrument is the personal computer."
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Sep 2007
Posts: 3,926
Veteran
|
|
Veteran
Joined: Sep 2007
Posts: 3,926 |
Okay, I'm on break. Let me try again. When you turn on a power switch it is considered "energized." Doing this from our notional amplifier's switch starts a timer connected to a relay which suppresses audio output until the power-on transient has passed. This is a one-shot device. The delay won't happen again until you cycle the unit's onboard power switch again, i.e., turn it off and back on. Therefore, if the switch is left on while the device is powered down, when you reintroduce power you will get an inrush transient as the device powers up, but with no delay as the relay has already been triggered. Therefore the transient will be passed to the speakers if they are on. Megathump to the max. Bad. Krunk says not do.  Is mo' bettah?
"My primary musical instrument is the personal computer."
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jan 2002
Posts: 7,913
Veteran
|
|
Veteran
Joined: Jan 2002
Posts: 7,913 |
You can buy a rack-mounted power distro that is designed to delay the power to the outlets for amps. Used it for years in a built-in rack at the listening room at GM, but can't remember the name of the brand!
IMO, every amp rack in a PA system should have one of these boys.
-Scott
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Sep 2007
Posts: 3,926
Veteran
|
|
Veteran
Joined: Sep 2007
Posts: 3,926 |
I especially like the "ergonomic design." Whaddya, gonna sit on it?
"My primary musical instrument is the personal computer."
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Oct 2008
Posts: 8,109
Veteran
|
|
Veteran
Joined: Oct 2008
Posts: 8,109 |
Quote:
I especially like the "ergonomic design." Whaddya, gonna sit on it?
Why oh WHY did you plant that visual in my mind??
(erase, erase...)
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
Quote:
I've been reading up on Mac's suggestions and am leaning towards the QSC - made in USA and has 6 year warranty. The Crown would be my next choice.
Another question...
My 'old' amp had an auto sensing which would turn the amp on when a signal is received. After a few minutes of no signal, it would shut off. This is important because the amp is not in an easily accessed area. Neither the QSC or Crown have this ability. I assume that leaving the amp on continually is not a good idea?
Does anyone know of audio signal sensor that would automatically turn power on/off to the amp? No, the Clapper won't cut it!
Thanks
For the record, my own personal choice would be for the QSC over the Crown. Just so you know.
What are you using for preamp? Many audio preamps feature AC connects on the rear, some marked, "Switched" which means that anything plugged in there will switch on and off with the preamp's front panel power switch.
If you don't have that, consider a common plug strip with built in switch, which can be placed closer to you, and plug the amp - and anything else related into that strip, using one switch to power all on and off.
BTW -- the sensing audio power switching stuff is a good way to have to send an amp to the repair technician on a regular basis. You see, the entire amplifier cannot be entirely cur off from the power line with this nifty accessory, leaving a path for transients, spikes and lightning strikes to make it into your amp and take out all sorts of delicate and expe$ive components. I like a physical power cutoff switch, thankyewverrmuch.
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2007
Posts: 1,616
Expert
|
|
OP
Expert
Joined: May 2007
Posts: 1,616 |
I don't use a preamp. I use a Logitech Duet to stream music from my computer and Pandora. The output from the Duet goes to the amplifier via RCA plugs. Volume and anything else is controlled via the Duet.
The power strip that shuts everything off when the master is powered down looks very interesting. I am not sure it would work for me as the Duet goes into a standby mode which really is not off. However, I am able to turn it off with a few extra steps from a remote. I'll read up on these and see if it would work.
A comment on the audio sensing switch - I suspect this may contributed to the Audiosource to fail twice. I recall several occasions during a storm where the amp switched on/off several times. And during soft music passages, the amp would cycle off/on a number of times.
Despite being connected to a voltage regulator and whole-house surge suppressor, it still managed to die twice in 3 years with sparse usage. Another reason to favor the QSC is the 6 year warranty.
Thanks everyone for the input.
R
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jun 2005
Posts: 7,697
Veteran
|
|
Veteran
Joined: Jun 2005
Posts: 7,697 |
Rachael, you're talking about listening to MP3's. You're not listening to CD quality much less audiophile. Read this: http://help.pandora.com/customer/portal/articles/90985-audio-qualityFor that level of audio quality most anything would work fine like Scott's $25 amp from Goodwill. Forget about how great the spec's are for QSC and the like. MP3's are compressed files for pete's sake. If you honestly can't tell or don't care about the difference between listening to a CD quality song in Real Band and that same song compressed to an MP3 at 128K then this whole discussion is academic. Basically anything would be fine as long is it's not humming and crackling. Bob
Biab/RB latest build, Win 11 Pro, Ryzen 5 5600 G, 512 Gig SSD, 16 Gigs Ram, Steinberg UR22 MkII, Roland Sonic Cell, Kurzweil PC3, Hammond SK1, Korg PA3XPro, Garritan JABB, Hypercanvas, Sampletank 3, more.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
Maybe her mp3 files are at higher bitrates or possibly even the no-loss Variable Bitrate.
Maybe she also wishes to listen to CDs.
Maybe she also wants hi fidelity to play BiaB, DAW and other sudio as well.
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2007
Posts: 1,616
Expert
|
|
OP
Expert
Joined: May 2007
Posts: 1,616 |
Bob,
Not only Pandora. My music collection is lossless FLAC. So to add to Mac's post: yes, yes and yes
R
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jan 2002
Posts: 7,913
Veteran
|
|
Veteran
Joined: Jan 2002
Posts: 7,913 |
As far as I know, variable bitrate .mp3 files are still lossy.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Dec 2011
Posts: 3,361
Veteran
|
|
Veteran
Joined: Dec 2011
Posts: 3,361 |
There's always the point about cumulative loss. That is, whatever the quality of the source material, you don't want to degrade it any further.
Just sayin'...
ROG.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Sep 2003
Posts: 8,333
Veteran
|
|
Veteran
Joined: Sep 2003
Posts: 8,333 |
I noticed that in the last few months amps weigh way less. I have 2 heavy duty ones. I also note that some new amps have 20 amp male plugs, the club thought they were 220v but it's specd at over 15 amps (most wiring)' so new copper, new plug and off you go.
John Conley
Musica est vita
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
Quote:
As far as I know, variable bitrate .mp3 files are still lossy.
That's not the point here.
Some call VBR "lossless" -- technicians know better, BUT -- my reply simply was trying to say that the poster's refernce to mp3 as being "128KBPS" *only* -- as in webstreaming, was not only erroneous, but rather condescending towards our lady's wish to have an amp with good spec.
Besides, it is now thoroughly debunked and a moot point, as the lady states that she listens to a lot of FLAC as well.
When I webstream a 128 audio file, I still listen to it on the very same reference monitoring system that I built for my recording and other music endeavors. At least I can be confident on what I am hearing, lossy or not.
But I've double-blindfolded quite a few who have told me that they can easily hear differences in the various compressed and even uncompressed digital formats. To date, nobody has scored 100%...
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jun 2005
Posts: 7,697
Veteran
|
|
Veteran
Joined: Jun 2005
Posts: 7,697 |
Oh yeah, 9 puonds for a 1000W stereo amp? Amazing. My old 500W Peavey has to weigh 40 pounds, maybe more. That thing is a real lump. Sounds good though. And then there's the new neo whatever magnets for speakers. That combo is how the new powered Class D PA speakers like the Yamaha DXR series put out 1100W and weighs 34 pounds. I've been looking to upgrade my stage rig and this new stuff is really good. Expensive too, I'm still trying to calibrate my "bang for the buck" meter.
Bob
Biab/RB latest build, Win 11 Pro, Ryzen 5 5600 G, 512 Gig SSD, 16 Gigs Ram, Steinberg UR22 MkII, Roland Sonic Cell, Kurzweil PC3, Hammond SK1, Korg PA3XPro, Garritan JABB, Hypercanvas, Sampletank 3, more.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Sep 2007
Posts: 3,926
Veteran
|
|
Veteran
Joined: Sep 2007
Posts: 3,926 |
Quote:
I'm still trying to calibrate my "bang for the buck" meter.
I'm sure Mr. Marr can help you out!
"My primary musical instrument is the personal computer."
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
The heavy weight of the older bipolar transistor power amplifiers was due to the fact that they had to incorporate a heavy "iron" AC power transformer. Since bipolar transistors are Current devices, that meant being able to supply the amplifier itself, which typically weighs less than a pound or two (driver circuit board plus output transistors and lightweight aluminum heatsink) with a voltage lower than the AC power input, transformed to high Current. At 50-60Hz, that requires a lot of iron laminations in the power transformer.
The weight savings in today's designs come from using modern Switching Power Suppy desings, which, while still needing to supply the lower voltage at a higher current, can do so without the need for the big mass of iron because the Switching Supply first rectifies the incoming AC to DC, then "chops" it up into AC at a much higher frequency, typically around 40KHz or higher. They still use transformers, but at that higher frequency the transformers are very small indeed by comparison.
The use of the FET (Field Effect) Power Transistor intead of the older Bipolar Silicon transistor also contributes to the lowered cost and weight of the modern power amp. Means we can control more power with less devices. And a few other good things.
An amplifier of any kind is but a modulated power supply.
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: Jun 2005
Posts: 7,697
Veteran
|
|
Veteran
Joined: Jun 2005
Posts: 7,697 |
Rachael, I wasn't being condescending.
Mac, that's all she referenced, streaming Pandora. Pandora's site says consumer stuff only receives it at 128K. At that bitrate, you don't need a good spec amp. How many times have we including you, suggested to people if you want good answers provide complete info in your questions? I've read her posts before, she knows the difference between mixing good audio in a home studio and streaming MP3's. If she's only talking about one and not the other so?? Sorry Rachael, I'm not deliberately talking past you here, this is for Mac. And how many times Mac have you said if on a budget pick up a good name 70-80's era stereo receiver at a yard sale? Or Goodwill like Scott said. Even a 2000 era cheapo Panasonic/Awia/Sony low end consumer home theater receiver is fine for this. And if a person can't hear the difference between an uncompressed wav file and an MP3 anyway then you still don't need a high spec amp do you? Therefore, my answer was complete, correct and not condescending. Just the facts, ma'am.
This brings up another point that we all should consider when thinking about new equipment. There's ear testing websites and we already have home studio setups. Test ourselves if we really can hear these differences or not. I admit I can some of the time. Other times not so much. It mainly depends on the freq range in the source material. Higher freq's are what starts to break up in compressed files and higher freq's are what older folks start to lose first. I can hear cymbals breaking up on some MP3's but mainly on small group stuff like trios where the drums are hot. But, on bigger band higher engergy stuff like traditional big band or TOP things, it's pretty hard to really hear that. For me it's becomming marginal as to whether it's worth it or not. I've been using an Alesis RA100 amp for years and I'm pretty sure that's as good as I will ever need for this stuff at home. You can buy one of those for $100 used all day long now. When I mix stuff after I get it to where I think it should be I deliberately boost the higher freq's above 9K a few db to allow for people with better hearing because my own hearing rolls off about there. I'll never know if that is appropriate or not but I think it is.
Bob
Biab/RB latest build, Win 11 Pro, Ryzen 5 5600 G, 512 Gig SSD, 16 Gigs Ram, Steinberg UR22 MkII, Roland Sonic Cell, Kurzweil PC3, Hammond SK1, Korg PA3XPro, Garritan JABB, Hypercanvas, Sampletank 3, more.
|
|
|
|
|
|
|
|
|
|
|
|
|
Off-Topic
|
Joined: May 2007
Posts: 1,616
Expert
|
|
OP
Expert
Joined: May 2007
Posts: 1,616 |
I took no offense to any comments; you would know if I did  . My earlier post did say that I listen to both Pandora and music streamed from my computer. Funny how some of these topics drift. I have always appreciated anyone taking time to respond - this is no exception. Again, thanks for all of the feedback. R
|
|
|
|
|
|
|
|
|
|
|
|
Ask sales and support questions about Band-in-a-Box using natural language.
ChatPG's knowledge base includes the full Band-in-a-Box User Manual and sales information from the website.
|
|
|
|
|
|
|
|
|
|
|
Band-in-a-Box® 2025 for Mac® users: Build 904 now available!
If you're already using Band-in-a-Box® 2025 for Mac®, make sure to grab the latest update! Build 904 is now available for download and includes the newest additions and enhancements from our team.
Band-in-a-Box® 2026 for Windows® users: Build 1237 is now available!
Already a Band-in-a-Box 2026 for Windows user? Stay up to date and download the build 1237 to get all the latest additions and enhancements.
PowerTracks Pro 2026 for Windows is Here!
PowerTracks 2026 is here—bringing powerful new enhancements designed to make your production workflow faster, smoother, and more intuitive than ever.
The enhanced Mixer now shows Track Type and Instrument icons for instant track recognition, while a new grid option simplifies editing views. Non-floating windows adopt a modern title bar style, replacing the legacy blue bar.
The Master Volume is now applied at the end of the audio chain for consistent levels and full-signal master effects.
Tablature now includes a “Save bends when saving XML” option for improved compatibility with PG Music tools. Plus, you can instantly match all track heights with a simple Ctrl-release after resizing, and Add2 chords from MGU/SGU files are now fully supported... and more!
Get started today—first-time packages start at just $49.
Already using PowerTracks Pro Audio? Upgrade for as little as $29 and enjoy the latest improvements!
Order now!
Band-in-a-Box 2026 for Windows Special Offers End Tomorrow (January 15th, 2026) at 11:59 PM PST!
Time really is running out! Save up to 50% on Band-in-a-Box® 2026 for Windows® upgrades and receive a FREE Bonus PAK—only when you order by 11:59 PM PST on Thursday, January 15, 2026!
We've added many major new features and new content in a redesigned Band-in-a-Box® 2026 for Windows®!
Version 2026 introduces a modernized GUI redesign across the program, with updated toolbars, refreshed windows, smoother workflows, and a new Dark Mode option. There’s also a new side toolbar for quicker access to commonly used windows, and the new Multi-View feature lets you arrange multiple windows as layered panels without overlap, making it easier to customize your workspace.
Another exciting new addition is the new AI-Notes feature, which can transcribe polyphonic audio into MIDI. You can view the results in notation or play them back as MIDI, and choose whether to process an entire track or focus on specific parts like drums, bass, guitars/piano, or vocals. There's over 100 new features in Band-in-a-Box® 2026 for Windows®.
There's an amazing collection of new content too, including 202 RealTracks, new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 5, two RealDrums Stems sets, XPro Styles PAK 10, Xtra Styles PAK 21, and much more!
Upgrade your Band-in-a-Box for Windows to save up to 50% on most Band-in-a-Box® 2026 upgrade packages!
Plus, when you order your Band-in-a-Box® 2026 upgrade during our special, you'll receive a Free Bonus PAK of exciting new add-ons.
If you need any help deciding which package is the best option for you, just let us know. We are here to help!
Band-in-a-Box® 2026 for Windows® Special Offers Extended Until January 15, 2026!
Good news! You still have time to upgrade to the latest version of Band-in-a-Box® for Windows® and save. Our Band-in-a-Box® 2026 for Windows® special now runs through January 15, 2025!
We've packed Band-in-a-Box® 2026 with major new features, enhancements, and an incredible lineup of new content! The program now sports a sleek, modern GUI redesign across the entire interface, including updated toolbars, refreshed windows, smoother workflows, a new dark mode option, and more. The brand-new side toolbar provides quicker access to key windows, while the new Multi-View feature lets you arrange multiple windows as layered panels without overlap, creating a flexible, clutter-free workspace. We have an amazing new “AI-Notes” feature. This transcribes polyphonic audio into MIDI so you can view it in notation or play it back as MIDI. You can process an entire track (all pitched instruments and drums) or focus on individual parts like drums, bass, guitars/piano, or vocals. There's an amazing collection of new content too, including 202 RealTracks, new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 5, two RealDrums Stems sets, XPro Styles PAK 10, Xtra Styles PAK 21, and much more!
There are over 100 new features in Band-in-a-Box® 2026 for Windows®.
When you order purchase Band-in-a-Box® 2026 before 11:59 PM PST on January 15th, you'll also receive a Free Bonus PAK packed with exciting new add-ons.
Upgrade to Band-in-a-Box® 2026 for Windows® today! Check out the Band-in-a-Box® packages page for all the purchase options available.
Happy New Year!
Thank you for being part of the Band-in-a-Box® community.
Wishing you and yours a very happy 2026—Happy New Year from all of us at PG Music!
Season's Greetings!
Wishing everyone a happy, healthy holiday season—thanks for being part of our community!
The office will be closed for Christmas Day, but we will be back on Boxing Day (Dec 26th) at 6:00am PST.
Team PG
|
|
|
|
|
|
|
|
|
|
|
|
Forums57
Topics86,048
Posts799,308
Members40,015
| |
Most Online44,367
Mar 4th, 2026
|
|
|
|
|
|
|
|
|
Dansk
Deutsch - Windows
Español
Français - Windows
Italiano - Windows
Nederlands
Polski
Português
Svenskt
русский
Japanese
Simplified Chinese
Traditional Chinese
Korean