|
Log in to post
|
Print Thread |
|
|
|
|
|
RealBand
|
Joined: Jan 2009
Posts: 63
Enthusiast
|
OP
Enthusiast
Joined: Jan 2009
Posts: 63 |
Hi,
I've been mostly running MIDI sequences, and doing the vocals live with that configuration recording the audio out of my separate PA Mixer. This has worked quite well in the past.
Today we were helping a friend of mine out who uses backing tracks, e.g. WAV or MP3, and we wanted to record the backing track to a track in RealBand and then play that track back and record his vocals on a second audio track.
We can record the backing track OK, and that plays back just fine. But when we enter record mode in RB we could not get the previously recorded audio (backing) track to play while recording the vocals.
I've probably missed it in searching the forums, but I haven't spotted anything that has helped me resolve this yet. I found the play and record checkbox in options for Audio, but that did not appear to make any difference.
Could this be a sound card limitation? That is, the sound card may only be able to play OR record but not do both at the same time. It is an on board sound card, on an MSI Motherboard.
If it is the sound card what external (USB, or other) sound card(s) would you recommend to resolve the issue?
Thanks,
Burt
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 22,165
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,165 |
Look for setting called full duplex
You are recording onto a separate track for the new vocals right? Highliting a new track other than the one you just recorded on? You can not record on the same track twice without recording over the existing material.
What soundcard is there now? What OS?
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Jan 2005
Posts: 4,900
Veteran
|
|
Veteran
Joined: Jan 2005
Posts: 4,900 |
I agree with rharv's post above. Make sure you have selected a clean and empty track. You cannot listen to the sound on a track you are recording to
Follow That Dream Sam Karaoke King -------------------- Turning that corner again - I have to keep following that dream, no matter what
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Jan 2009
Posts: 63
Enthusiast
|
|
OP
Enthusiast
Joined: Jan 2009
Posts: 63 |
Thanks,
I should have been clearer.
The backing track is recorded on Track 1, which is set to be mono-audio
We then set empty track 2 to also be mono-audio, and track 2 is highlighted/selected.
We click the record button, the metronome count in starts and we are recording to track 2 but we cannot hear the previously recorded backing track that is on Track 1.
So, no we are not trying to record over the top of the previously recorded track.
This running under Windows XP Pro, the "Sound Card" is what is built into the MSI mother board. It is an MSI K8MM-ILSR Motherboard with VIA/Realtek ALC655 sound chip.
So I'm thinking that might be the limiting factor and that the sound card may not support playback while recording. Just for grins I'm trying to install/update the sound driver again just in case. As expected updating the driver did NOT correct the problem.
The MB specs say that it is an AC'97 link controller integrated in VIA VT8237, 6 channels software audio codec ALC655, Compliance with AC97 v2.3 Spec and Meets PC2001 audio performance requirement.
As mentioned before, I normally use MIDI sequences for my own backing "tracks" and set an unused track in RB to audio, and record the output from our mixer/pa which includes the MIDI synth audio output, my guitar, and our vocals. That of course works just fine since the sound card does not need to play anything back at that point.
Note there is no problem with the sound card playing back if we have recorded a track in RB and then play it back, or any other playback functions with the sound card.
It is only when there is a previously recorded audio track that is loaded into RB (say as track 1) and we attempt to record to another track (in this example track 2) and want to have Track 1 playing while we are recording to Track 2.
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 22,165
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,165 |
That is weird
Again I would look for a 'full duplex' setting in the soundcard
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
Can you just hit Play and hear the first track play back by itself?
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 22,165
Veteran
|
|
Veteran
Joined: May 2000
Posts: 22,165 |
"Note there is no problem with the sound card playing back if we have recorded a track in RB and then play it back, or any other playback functions with the sound card.
"
I do not work here, but the benefits are still awesome
Make your sound your own!
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Jan 2009
Posts: 63
Enthusiast
|
|
OP
Enthusiast
Joined: Jan 2009
Posts: 63 |
Thanks Mac,
Yes, the previously recorded track plays back just fine if you hit the play button in RB. When hitting Record we do not hear that previously recorded track, but we can record fine on the empty track.
I've checked for a duplex option on the sound driver in WinXP for this "sound card" and do not see it, so I'm suspecting that the sound card and/or driver is the limiting factor here.
Does anyone have a good suggestion for an add on sound "card" you are using that supports full duplex operation?
Burt
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
I have used several different RealTek built in soundcards with both PT and RB (virtually identical engines) and have been able to do what you want to do. There may be different RealTek designs out there, but if your computer is even "relatively" new, it should be able to do this.
I suspect a setting somewhere is preventing this.
Please check, inside of RealBand, Prefs -> 2Audio -> and about halfway down the window that opens on the LH side, see if "Full Duplex(Record/Play at same time)" is checked to true.
If it is, try UNchecking it, say okay, then go right back and check it again and say Okay. Might be "stuck" somehow...
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Jan 2009
Posts: 63
Enthusiast
|
|
OP
Enthusiast
Joined: Jan 2009
Posts: 63 |
Thanks Mac, That appeared to do the trick.. That is I went in and cleared, exited, then re-checked the full duplex option in RB Audio configuration. Didn't get a chance to test until a few minutes ago, but now I can play the WAV file loaded into track 1 and record on from the mic/PA on track 2. So that is great. But there is another wrinkle. The output from the sound card is being fed into the playback input on my Kustom PA, and the record out from the PA is routed to the Aux input on the computer (sound card). The record output comes after the mixer portion of the PA and before the final Monitor and Master level controls and equalizers. The playback input is after the final Monitor and Master equalizers and definitely does NOT route back in any way to the record output or the mixer portion of the PA. Even with the playback volume controls set to 0 so no sound is heard through the PA speakers so there could be nothing picked up via the mics track two winds up with a low volume recording of the WAV in track 1. If I sing or talk into the mic that is also recorded. If I turn the volume slider on track 1 to 0 then track 2 only gets the microphone input and not the backing track audio. Again the signal path for the playback input on the PA does NOT route through any of the PA inputs and also from previous recording attempts did not appear to route through the record outputs, so I don't think that would be the issue here but I'll check again. That is, in order to record audio coming from the computer I would have to move the audio output from the playback input jacks and bring it in through the PA mixer, which is not what I'm currently doing. Have you run into this before? is there some option or setting that I'm missing that is causing the audio being played back on track 1 to be recorded on track 2? If you haven't seen this before I'll try pulling things out of the case and disconnect the aux input to the PC, and no the PC does NOT have a microphone built in.  Thanks again, Burt
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
Unless your mixer has a specified "Control Room" monitoring setup, I suspect that you can't use it like a recording mixer as you have currently hooked up.
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Jan 2009
Posts: 63
Enthusiast
|
|
OP
Enthusiast
Joined: Jan 2009
Posts: 63 |
Thanks Mac, Actually it was easier than that  I went back and checked the sound card and there were two "mixer" controls in the optional recording settings. When I made them visible both of them were slightly above 0!!!! I never set those so they must have been defaulted to that. Knocked them both down to 0, and the problem went away. Hopefully user info for someone else if they have a similar problem some day. Appears to be working fine now, can play the recorded WAV on track 1, record on other tracks, and as long as the mic is isolated where it doesn't pick up any bleed it works well. Since we use headphones for monitor I just need to make sure that I feed the playback from the computer / RB into the mixer I'm using for the headphones and we should be good to go for the actual recording sessions. Thanks again, Burt
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Aug 2006
Posts: 8,502
Veteran
|
|
Veteran
Joined: Aug 2006
Posts: 8,502 |
I would suggest as a very inexpensive option a small mixer, like abehringer 802 this will allow you to monitor the mix at the mixer and solve this issue for you. Here is the little guy now http://pro-audio.musiciansfriend.com/product/Behringer-Xenyx-802?sku=631263
HP Win 11 12 gig ram, Mac mini Sonoma with 16 gig of ram, BiaB 2025, Realband, Reaper 7, Harrison Mixbus 9 32c , Melodyne 5 editor, Presonus Audiobox 1818VSL, Presonus control app.
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Jun 2010
Posts: 1
Newbie
|
|
Newbie
Joined: Jun 2010
Posts: 1 |
You can also try to use Macvide Audio Recorder.It’s prog can records many different formats of sound.Try.
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Jan 2003
Posts: 1,942
Expert
|
|
Expert
Joined: Jan 2003
Posts: 1,942 |
I am an owner of the Behringer 802 and I wouldn't be without it.
Been using it now for about 8 years and it still serves me well.
It's been there when I've recorded about 5 CDs. It's a darn good
mixer. Love it!
Cant go wrong for $59.99. I think 8 years ago I paid $39 for mine.
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: Dec 2000
Posts: 12,672
Veteran
|
Veteran
Joined: Dec 2000
Posts: 12,672 |
Ditto, although mine's an 802A. It's been great for a guy like me on a budget.
John Laptop-HP Omen I7 Win11Pro 32GB 2x2TB, 1x4TB SSD Desktop-ASUS-I7 Win10Pro 32GB 2x1.5TB, 2x2TB, 1x4TB SATA BB2025/UMC404HD/Casios/Cakewalk/Reaper/Studio One/MixBus/Notion/Finale/Dorico/Noteworthy/NI/Halion/IK http://www.sus4chord.com
|
|
|
|
|
|
|
|
|
|
|
|
|
RealBand
|
Joined: May 2000
Posts: 38,502
Veteran
|
|
Veteran
Joined: May 2000
Posts: 38,502 |
The OP should look into aftermarket sound card designed for multitrcking music firat.
The built in soundcard is a recipe for additive noise when adding tracks.
--Mac
|
|
|
|
|
|
|
|
|
|
|
|
Ask sales and support questions about Band-in-a-Box using natural language.
ChatPG's knowledge base includes the full Band-in-a-Box User Manual and sales information from the website.
|
|
|
|
|
|
|
|
|
|
|
Video: Band-in-a-Box® 2025 for Mac®: VST3 Plugin Support
Band-in-a-Box® 2025 for Mac® now includes support for VST3 plugins, alongside VST and AU. Use them with MIDI or audio tracks for even more creative possibilities in your music production.
Band-in-a-Box® 2025 for Macs®: VST3 Plugin Support
Video: Band-in-a-Box® 2025 for Mac®: Using VST3 Plugins
Join the conversation on our forum.
Band-in-a-Box 2025 for Mac Videos
With the release of Band-in-a-Box® 2025 for Mac, we’re rolling out a collection of brand-new videos on our YouTube channel. We’ll also keep this forum post updated so you can easily find all the latest videos in one convenient spot.
From overviews of new features and walkthroughs of the 202 new RealTracks, to highlights of XPro Styles PAK 8, Xtra Styles PAKs 18, the 2025 49-PAK, and in-depth tutorials — you’ll find everything you need to explore what’s new in Band-in-a-Box® 2025.
Reference this forum post for One-Stop Shopping of our Band-in-a-Box® 2025 Mac Videos — we’ll be adding more videos as they’re released!
Band-in-a-Box 2025 for Mac is Here!
Band-in-a-Box® 2025 for Mac is here, packed with major new features and an incredible collection of available new content! This includes 202 RealTracks (in Sets 449-467), plus 20 bonus Unreleased RealTracks in the 2025 49-PAK. There are new RealStyles, MIDI SuperTracks, Instrumental Studies, “Songs with Vocals” Artist Performance Sets, Playable RealTracks Set 4, two new sets of “RealDrums Stems,” XPro Styles PAK 8, Xtra Styles PAK 19, and more!
Special Offers
Upgrade to Band-in-a-Box® 2025 for Mac with savings of up to 50% on most upgrade packages during our special—available until July 31, 2025! Visit our Band-in-a-Box® packages page for all the purchase options available.
2025 Free Bonus PAK & 49-PAK Add-ons
We've packed our Free Bonus PAK & 49-PAK with some incredible Add-ons! The Free Bonus PAK is automatically included with most Band-in-a-Box® for Mac 2025 packages, but for even more Add-ons (including 20 Unreleased RealTracks!) upgrade to the 2025 49-PAK for only $49. You can see the full lists of items in each package, and listen to demos here.
If you have any questions, feel free to connect with us directly—we’re here to help!
Band-in-a-Box 2025 Italian Version is Here!
Cari amici
È stata aggerate la versione in Italiano del programma più amato dagli appassionati di musica, il nostro Band-in-a-Box.
Questo è il link alla nuova versione 2025.
Di seguito i link per scaricare il pacchetti di lingua italiana aggiornati per Band-in-a-Box e RealBand, anche per chi avesse già comprato la nuova versione in inglese.
Band-in-a-Box 2025 - Italiano
RealBand 2025 - Italiano
Band-in-a-Box 2025 French Version is Here!
Bonjour à tous,
Band-in-a-Box® 2025 pour Windows est disponible en Français.
Le téléchargement se fait à partir du site PG Music
Pour ceux qui auraient déjà acheté la version 2025 de Band-in-a-Box (et qui donc ont une version anglaise), il est possible de "franciser" cette version avec les patchs suivants:
BIAB 2025 - francisation
RealBand 2025 - francisation
Voilà, enjoy!
Band-in-a-Box 2025 German Version is Here!
Update Your Band-in-a-Box® 2025 to Build 1128 for Windows Today!
Already using Band-in-a-Box 2025 for Windows®? Download Build 1128 now from our Support Page to enjoy the latest enhancements and improvements from our team.
Stay up to date—get the latest update now!
|
|
|
|
|
|
|
|
|
|
|
|
Forums58
Topics84,308
Posts777,559
Members39,615
| |
Most Online25,754
Jan 24th, 2025
|
|
|
|
|
|
|
|
|
Dansk
Deutsch - Windows
Español
Français - Windows
Italiano - Windows
Nederlands
Polski
Português
Svenskt
русский
Japanese
Simplified Chinese
Traditional Chinese
Korean